where to buy chainsaw oil Related Question:
What oil is best for chainsaw chain?
Rapeseed-based (usually called canola) oil is currently the most common environmentally compatible chain-and-bar lubricant. Vegetable-based oils are triglycerides or natural esters that come from agricultural crops.
Can you use any oil for chainsaw bar oil?
Generally, chainsaws can handle a wide range of lubricants. Vegetable and canola oils work well, and automobile motor oil will too, as long as you observe the SAE ratings and use the appropriate oil weight for the season. Always use fresh, never used, oils.
Can you use regular motor oil in a chainsaw?
If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Is chainsaw oil the same as regular oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
What is a substitute for chainsaw bar oil?
Vegetable Oil Vegetable oil is one of the safest alternatives available to oil your chainsaw. It is completely non-toxic and biodegradable, and can even be used to trim live trees without danger of hurting you or the plants! And boy is it cheap – you may even have it in your kitchen right now.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can you use vegetable oil in a chainsaw?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
What is special about chainsaw oil?
Chainsaw bar oil is lubricant that is designed to reduce friction between the chain and bar. An oil reservoir releases the oil onto the bar.
How much bar oil should a chainsaw use?
When to Oil Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
Can I use 2 stroke oil for chainsaw?
Modern two stroke chainsaws do not require generic brand oils to operate at temperatures and rpms that are comparable to those of generic brand oils. Our recommendation is to use only high quality two stroke oil designed for air cooled high performance engines when using your modern two-cycle engine.
Can I use wd40 on chainsaw?
We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.
Can I use olive oil for bar and chain oil?
Olive/vegetable oil is probably not as good as bar oil, which is thicker than motor oil, but for light cutting should be just fine.
Can you use sunflower oil in a chainsaw?
If using a saw to cut meat, then vegetable oil is the obvious choice so the meat tastes good (you can use sunflower, canola, palm oil etc).
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.