Check and replace bar and chain oil regularly to reduce friction, keep the saw from wearing out faster, and to make cutting easier. Be sure to use bar and chain oil, Not regular motor oil. Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
This is different than the oil that you mix with your gas to provide lubrication to the engine, and I’m going to describe below the importance of this task and explain how to oil your chainsaw for both the safety and care of your saw. Most saws come with a sample bottle of oil and suggestions of which oil to by- but for the most part, the oil is that same from one brand to the next. Saws are designed to feed oil as it runs, so most tanks are large enough to hold enough oil for a full tank of gas.
At Gardening Products Review, we highly recommend oil manufactured for this specific use. Chainsaw shown in this video tutorial is the Redback 40V 12″ Li-Ion Cordless Chainsaw. The bar & chain oil featured in this video is Husqvarna Bar & Chain Oil – 1 Gallon.
Our bar and chain oil is specifically compounded to provide extra high tackiness and prevent “Throw off” even under adverse weather conditions. Used motor oil contains metal shavings that reduce the life of your bar and chain. Lubricating your bar and chain with used motor oil will void your warranty.
where to put chainsaw bar oil Related Question:
How do you add oil to a bar?
The steps are quick and easy: Set your chainsaw on a level surface, bar side down so that it lays flat. Allow a minute for the oil to settle, then unscrew the cap to the saw’s bar and chain oil reservoir. Using a small funnel, slowly pour the bar and chain oil into the reservoir, taking care not to overfill.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
How often should I oil my chainsaw chain?
Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
How often should I oil my chainsaw?
It is recommended that you grease the bearing in the tip of the bar each time you refuel. Make sure to grease the tip at the end of the day as well to help prevent moisture from entering the bearing as the bar cools.
Can I use 2 stroke oil for chainsaw bar oil?
Can You Use 2 Cycle Oil As Bar Oil? You should only use two-cycle oil as the mix, never as a chainsaw bar oil alternative. Using two-cycle oil on the bar will not provide enough tackiness to stick to the chainsaw chain in the summer months. Two-cycle oil also will not work in the winter.
Can I use WD40 as chainsaw oil?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Do you need to oil chain on chainsaw?
To work properly, chainsaw chains and bars must be lubricated.In the past, most operators have used petroleum-based oils. When a chain saw is used, virtually all of the lubricant ends up in the environment.
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
What does 10W30 mean?
The 10W30 designation on engine oil means that the viscosity of the oil is rated at 10W when an engine is cold and 30 when the engine is hot. This is different than an oil labelled 5W30, which has a thinner viscosity when the engine is cold at 5W.
Can any oil be used for chainsaw bar oil?
If you have the choice, use SAE30 motor oil when it’s hot outside and SAE10 motor oil when it’s cold because the variations in oil viscosity are better for certain temperatures. Hydraulic oil is similar to motor oil and you can use it as a chainsaw bar oil substitute when you have nothing else available.
Can I use 5W30 for bar oil?
You’ll be fine.
Can you over oil a chainsaw?
Although a chain saw always requires the moisture that oil provides during the saw’s operation, too much oil isn’t good. When the oil adjustment is set too high, the oil is subject to drip from the chain and run down the guide bar.