When the saw teeth become chipped, damaged or dull, the chainsaw likely won’t cut straight, especially if more teeth are affected along one side of the chain. Sharpen the teeth uniformly using a file and file guide, or take it to professional for sharpening. Madsen’s recommends using a grinder rather than a file, if you want to avoid taking it to a professional.
The most probable reason why a chainsaw pulls either to the right or left during a cut is because it was sharpened unevenly. Keep working the side which you feel lacks attention, and eventually the chainsaw should start going as straight as new. The teeth have to be equally sharp on each end to make the chainsaw work straight.
Dull cutters damaged by rocks can cause a chain to cut crooked. It’s important to remove all damage from cutters prior to cutting. Cutting with a dull chain can accelerate wear to the bar and chain.
why chainsaw cutting crooked Related Question:
How do I stop my chainsaw from cutting crooked?
Check the size of the top plates, which sit on the longer sections of each tooth on the chain. These top plates should be the same size. If some are shorter than others, file the longer ones down to match. Keep the same angle on all the top plates as you file – angles that don’t match also can cause curved cutting.
What would cause a chainsaw to cut crooked?
Uneven top plates can cause a chain to cut crooked. It’s important to keep all top plates equal length. Dull cutters damaged by rocks can cause a chain to cut crooked. It’s important to remove all damage from cutters prior to cutting.
Can a bent chainsaw bar be straightened?
Solid body bars with replaceable noses can be straightened by hammering with the bend peak up on a flat anvil. Laminated bars need a piece of rubberized belting of approximate 1/4″ thickness between bar and anvil to properly hammer straighten .
When should you throw away a chainsaw chain?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
Do you flip the bar on a chainsaw?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
Can you straighten a chainsaw blade?
If you just have a few drive links twisted a vice will usually straighten them out . If however you bent the drivers up in the chain it’s self it might not be a bad idea to just change them rather than take a chance of breaking a chain .
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How many times can you sharpen a chainsaw?
Cutters can be sharpened up to 10 times or more before the chain needs replacing. If your cutters are worn unevenly after a few sharpenings, a professional can regrind them to uniform shape. If you use the same chain for a few years, then buy a new one, the new one won’t mesh smoothly with the sprocket and bar.
How long should a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Why is there a hole in a chainsaw bar?
The hole is part of the manufacturing process when the bar is made at the factory. The milling and heat tempering machines anchor to it and the tail slot. Making a living with a saw since age 16.
What is the best angle for a chainsaw chain?
The sharpening angle will generally be between 25° and 35° – the harder the wood, the greater the angle. To maintain the correct angle, we recommend that you use a sharpening grid or a filing gauge as an aid.
Why does my chainsaw go blunt so quickly?
What is this? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast. It won’t be hard to notice whether the wood that you’re cutting is dirty or not.
Why does my chainsaw chain dull so quickly?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.