At Gardening Products Review, we highly recommend oil manufactured for this specific use. Chainsaw shown in this video tutorial is the Redback 40V 12″ Li-Ion Cordless Chainsaw. The bar & chain oil featured in this video is Husqvarna Bar & Chain Oil – 1 Gallon.
At Gardening Products Review, we highly recommend oil manufactured for this specific use. Chainsaw shown in this video tutorial is the Redback 40V 12″ Li-Ion Cordless Chainsaw. The bar & chain oil featured in this video is Husqvarna Bar & Chain Oil – 1 Gallon.
Electric chainsaws don’t require added oil, but there is a way you will use oil with your electric chainsaw. Electric chainsaws have specific bar and chain lubrication oil that is to be used on them. Although electric chainsaws do not use gasoline and oil as a gasoline-powered chainsaw would, you will need to lubricate the bar and chain as you would any chainsaw.
Use replacements if you run out: You can also buy lubricants that can substitute bar oil and allow your saw to run for short periods without actual bar oil, such as WD-40, cooking spray oil, or vegetable oil. You can use engine oil: Standard motor oil can be used in place of bar oil. You would need to check and fill your bar oil tank more often if motor oil is used instead. I would say that motor oil does provide enough lubrication, but it possesses a slightly higher viscosity which is not ideal for use in a chainsaw.
why does a chainsaw need oil Related Question:
Will a chainsaw work without oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
What happens if you don’t oil a chainsaw?
No bar oil equals increased friction and heat. That adds up to a huge increase in chain and bar wear. Without bar oil, the chain teeth, drivers and links will all wear far more quickly. The increased friction can cause teeth to break.
What is the use of chainsaw oil?
To prevent this, chainsaw manufacturers make bar oils matched to the air temperature and the saw in which it is operated. Although they don’t disclose the weight of their oil, the University of Missouri Extension recommends in lieu of using a bar oil, select SAE 30 weight oil in summer and SAE 10 in winter.
Can I use WD40 as chainsaw oil?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
What’s the difference between chainsaw bar oil and regular oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
How much chain oil should chainsaw use?
When to Oil Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
Do Electric chainsaws need oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
Can I use vegetable oil instead of bar and chain oil?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
Can I use regular oil for chainsaw bar?
Generally, chainsaws can handle a wide range of lubricants. Vegetable and canola oils work well, and automobile motor oil will too, as long as you observe the SAE ratings and use the appropriate oil weight for the season. Always use fresh, never used, oils.
What is the best thing to clean a chainsaw with?
In a well-ventilated area, take a bucket and mix one cup of ammonia with one gallon of water. Place the chainsaw chain in this solution and let it soak for 15 minutes. Put on a pair of thick rubber gloves for protection. Then, use a soft-bristled toothbrush to scrub each section of the chain until it’s free of debris.
Can you use engine oil as bar oil?
If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Can I use gear oil as bar oil?
Theoretically, you may still be able to use gear oil for your chainsaw. However, you need to understand that gear oil is actually thicker than most oils. Its thickness may not be ideal for a chainsaw because of how it won’t be able to properly lubricate the bar and chain.
Can I use 2 stroke oil for chainsaw?
Modern two stroke chainsaws do not require generic brand oils to operate at temperatures and rpms that are comparable to those of generic brand oils. Our recommendation is to use only high quality two stroke oil designed for air cooled high performance engines when using your modern two-cycle engine.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
How often do you change chainsaw oil?
HOW LONG DO 2-STROKE OILS LAST FOR? Two- stroke oil will last for a couple of years when it is not mixed with petroleum. Once mixed with petroleum we would not recommend keeping for more than 3-4 months in a sealed air tight approved storage container.