Generally, a fully functional chainsaw should cut straight and smooth, but if this does not happen, your chainsaw is likely to be faulty. The chainsaw bar can cause the chainsaw not to cut woods straight. The first step to solving any chainsaw problem is to understand the type of chainsaw suitable for your needs and how it operates.
When the saw teeth become chipped, damaged or dull, the chainsaw likely won’t cut straight, especially if more teeth are affected along one side of the chain. Sharpen the teeth uniformly using a file and file guide, or take it to professional for sharpening. Madsen’s recommends using a grinder rather than a file, if you want to avoid taking it to a professional.
Dull cutters damaged by rocks can cause a chain to cut crooked. It’s important to remove all damage from cutters prior to cutting. Cutting with a dull chain can accelerate wear to the bar and chain.
The most probable reason why a chainsaw pulls either to the right or left during a cut is because it was sharpened unevenly. Keep working the side which you feel lacks attention, and eventually the chainsaw should start going as straight as new. The teeth have to be equally sharp on each end to make the chainsaw work straight.
how to stop a chainsaw Related Question:
What is a chainsaw brake?
One of the most important chainsaw safety features is the chain brake, which stops movement of the chain in the event of kickback during operation. The chain brake is activated when the front hand guard, located near the saw’s upper handle, moves rapidly toward the chainsaw operator.
How do you stop a chainsaw from moving?
Correcting the problem requires adjusting the idle screw – usually marked “I” – on the carburetor. The idle screw usually is near or behind the air filter. Adjust the screw to restrict fuel delivery by turning it clockwise with a screwdriver until the chain stops turning. The saw must be running when you do this.
Can a chainsaw cut a person?
Flesh is no match for a chainsaw, it could probably cut through it pretty much forever without wearing out. Bones may be slightly tougher, but they are rigid and a chainsaw will likely be able to cut through them without much problem – though it will probably dull the blade more than wood.
What causes a chainsaw to stop?
A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
What happens if you run a chainsaw with the brake on?
Running a chainsaw with the brake on can be dangerous for you and anyone in your vicinity. The chainsaw will not cut, but it still creates sparks that can cause fires or startle nearby pets. It also doesn’t allow the saw to cool down enough which increases the likelihood of overheating and breaking down.
What does the choke do on a chainsaw?
The choke position increases the richness of the air and fuel mixture the carburetor sprays into the cylinder. With the master control lever in the choke position, the flow of fuel into the engine increases and the flow of air decreases.
What is idling chainsaw?
If the chainsaw won’t stop spinning when idling, or it’s smoking when it idles, it’s getting too much fuel and running rich, so you’ll need to back it down a bit. If it’s accelerating too slowly, or sputters and jumps erratically when idling, it’s got too little fuel and needs more.
Why does my chainsaw stop when idling?
Blocked or damaged Idle Port – Check the idle port Oil, dirt, and debris can block them, preventing the air from flowing into the engine. If the idle port of your chainsaw gets blocked or damaged, your chainsaw won’t stay running. Check the idle port for damage or blockage.
Can a chainsaw cut bone?
Yes, but it’s VERY messy. A chainsaw is basically a handheld cross-cut saw, designed to cut against the grain, A hacksaw, or even a ripsaw, would be a better tool, though obviously not as fast. Their smaller teeth mean less damage to the bone, and less flinging of bits… Chainsaw cuts bone just fine.
How do you start a stubborn chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
When should you throw away a chainsaw chain?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
Should you run a chainsaw at full throttle?
Engine Protection Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Should a choke be open or closed?
Should Choke Be Open Or Closed When Running? Having been in operation over the last few days, a gas engine that is still warm doesn’t require an choke. When it is warm, the fuel can evaporate quickly. It is recommended you close the choke the most if the engine is cold outside and it is warming outside.
Why do you need a choke?
A choke valve is sometimes installed in the carburetor of internal combustion engines. Its purpose is to restrict the flow of air, thereby enriching the fuel-air mixture while starting the engine.