Issues that usually cause a chainsaw to keep cutting out include bad fuel, clogged carburetor, fuel lines, etc. In general, a chainsaw that starts but keeps cutting out is because the engine is not receiving the required fuel and air to keep it running. High-Speed Fuel Adjustment: The high-speed fuel adjustment controls the fuel proportion in the combustible air-fuel mixture when the chainsaw is running at cutting speed.
Try to relax and read our guide to possibly find the reason why your chainsaw won’t stay running. If the idle port of your chainsaw gets blocked or damaged, your chainsaw won’t stay running. If you have more chainsaw questions, here at Canberra Diamond Blade, we are happy to help! In the meantime, check out our other chainsaw articles answering questions like if it’s worth sharpening a chainsaw chain.
If you use it too much while it’s overheating, it’s possible you may burn out the engine or pistons causing you to have a broken chainsaw that will either need to be repaired or replaced. Chainsaws generally cut out after starting because the engine gets too little or too much fuel from the carburetor. The most common problems why a chainsaw does not stay running are: Spark Switch/Plugs.
A clogged air filter is usually the most common reason as to why your chainsaw keeps on stalling. Re: Chainsaw won’t re-start when Hot Typically when a chainsaw wont start when warmed but starts and runs fine when cool, it’s because the air/fuel ratio is too rich. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed.
why does chainsaw keep stalling Related Question:
Why does my chainsaw keep cutting out?
The main culprit behind a chainsaw engine that keeps cutting out is usually a dirty or wrongly adjusted carburetor. A faulty carburetor fails to supply the correct air-fuel mixture, also called the “charge”, to the engine. Causing the engine to cut out or stall.
Why does my chainsaw stall when I give it gas?
Carburetor Adjustment An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw stalls while it’s idling, adjusting the idle screw, which usually is marked LA, should help.
Why does my chainsaw dies under load?
If the mixture of oil to fuel is too rich, too much oil is in the fuel and it leads to the engine losing power and dying. Open the fuel cap and pour the old fuel out of the tank into a disposable container. Mix new fuel in a gas can with a ratio of 50 to 1.
Why does my Stihl chainsaw bog down when I give it gas?
The Job of the Carburetor One controls the fuel mixture when the engine is idling, one controls it when the engine is operating at low speed and one is for high-speed fuel control. When the saw bogs down during cutting, it’s usually the high-speed screw you need to adjust.
Why does my chainsaw dies when I turn it sideways?
Because the fuel covers the jets. When the bar points down or the saw is held sideways the jets no longer have fuel to cover them, it is air. The saw then runs lean and dies.
Why does my chainsaw rev too high?
The throttle valve (butterfly) simply cuts off the supply of combustible air/fuel and the engine stops. If this adjustment is set too high, the high idle speed will cause the centrifugal clutch to engage and the chain will run. This is a dangerous condition and should never be allowed.
Can you clean a chainsaw carburetor without taking it apart?
To clean a carb, you have to take it apart. If it needs cleaning, the parts that need cleaning can’t be seen from the outside.
How do you clean a carburetor without removing it?
To clean a motorcycle carburetor without removing it, you’ll need to remove the bowls at the bottom of the carburetor. Once the bowls are removed, spray some carburetor cleaner up inside, wait a few minutes, then spray again to ensure coverage. Then replace the bowls and start the motorcycle to assess how it runs.
How do you clean a 2 stroke carburetor without removing it?
Vacuum away any loose dirt, dust, debris, grime, and great on the surface with a handheld and cordless vacuum. Lay out rags or cloths at the base of the carburetor to catch runoffs and protect the surfaces. Apply the carburetor and choke cleaner in thin, even coats. Then, wait for it to settle and work its magic.
Why does my Stihl chainsaw stall?
A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
Why does my Stihl chainsaw loses power?
When your Stihl MS 170 chainsaw drops its power under full load, it generally means there is an improper mixture of fuel and air in your carburetor. When you depress the trigger, a vent on the carburetor opens, allowing more gas to reach the mixing chamber.
Can you spray carb cleaner in chainsaw?
You can use Sea Foam Spray to clean your chainsaw carburetor effectively. Sea Foam spray has a petroleum cleansing solvency. And adds lubricity to various components of the carburetor. It is a fine cleaning agent for chainsaw carburetors.
Is Sea Foam safe for chainsaws?
At Sea Foam, we recommend overcoming saw starting issues by adding 2–4 ounces of Sea Foam Motor Treatment to a low tank of fuel, running it for about five minutes, then letting it sit a night or two to soak or clean. Add fresh fuel and proper two-stroke oil before operating and it’ll be good to go.
Can you use wd40 to clean a carburetor?
WD-40 Specialist® Carb/Throttle Body & Parts Cleaner with attachable precision straw is the only all-in-one carburetor cleaner spray you will need to clean your carburetor, throttle body, and unpainted metal parts. What makes this cleaner unique is the dual-action cleaning system.