Generally, a fully functional chainsaw should cut straight and smooth, but if this does not happen, your chainsaw is likely to be faulty. The chainsaw bar can cause the chainsaw not to cut woods straight. The first step to solving any chainsaw problem is to understand the type of chainsaw suitable for your needs and how it operates.
When the saw teeth become chipped, damaged or dull, the chainsaw likely won’t cut straight, especially if more teeth are affected along one side of the chain. Sharpen the teeth uniformly using a file and file guide, or take it to professional for sharpening. Madsen’s recommends using a grinder rather than a file, if you want to avoid taking it to a professional.
Dull cutters damaged by rocks can cause a chain to cut crooked. It’s important to remove all damage from cutters prior to cutting. Cutting with a dull chain can accelerate wear to the bar and chain.
Most of the time when a saw won’t cut straight, it’s caused by a problem with the saw chain. Most of the time, when a saw won’t cut straight, the chain is the culprit. Since a saw chain is a “Team” of cutter teeth, the cut will pull in the direction of the side whose cutter teeth take the biggest bites.
Your chain will have links on both sides of the chain. As I mentioned earlier, the chain is most likely the root cause of your problem, but if that’s not it, then it could also be your chainsaw bar. Use your gauge tool to clean the oil hole on both sides of the bar, to keep your chain running smoothly.
why does my chainsaw always cut to the right Related Question:
How do I stop my chainsaw from cutting crooked?
Check the size of the top plates, which sit on the longer sections of each tooth on the chain. These top plates should be the same size. If some are shorter than others, file the longer ones down to match. Keep the same angle on all the top plates as you file – angles that don’t match also can cause curved cutting.
What makes a chainsaw cut to the left?
If the chain is cutting to the left that means the right teeth on the chain are longer, and vise versa. To correct, sharpen only the side with the longer teeth. If the bar has worn unevenly it will also cause the chain to not cut straight.
Why does my chainsaw not cut square?
Most of the time when a saw won’t cut straight, it’s caused by a problem with the saw chain. When a saw won’t cut straight, the first component most users look at is the bar. It seem logical a bent bar would cause this, because it is is what guides the chain.
What makes a chainsaw cut in a curve?
Two main reasons will cause the chain to cut on a curve. The most common reason is from improper hand filing. If one side of the teeth is more heavily damaged, sharpening them down will make them smaller than the other side.
How often do you need to sharpen a chainsaw?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
How long does a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
Why does my chainsaw burn the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
Why does my chainsaw chain keep coming loose?
Chain Not Set Properly One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
What type of chainsaw chain cuts the fastest?
A full chisel chain is a chain with square cornered teeth, and they’re known for being the fastest cutting blade shape available. A full chisel chain also has a higher number of teeth than other chain options(full chisel is also known as a standard chisel chain).
How much does it cost to have a chainsaw sharpened?
A typical chainsaw can be sharpened up to 10 times before it’s time for a replacement. The cost to have a chainsaw sharpened ranges from $13 to $16. The average cost per chainsaw sharpening is $14.50 for people who choose to have their chainsaws professionally sharpened.
Why is my chainsaw bar smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Is it worth sharpening a chainsaw?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Are chainsaw bars hardened?
The solid chainsaw bar production begins with a solid bar of steel. The machine laser cuts the steel to the desired basic shape. That includes the outer contour, bores, and elongated hole. Looking at the process, the laser makes very little waste in the cut, and Stihl even reclaims the leftover steel.