Common reasons behind chainsaw overheating are a wrong oil/fuel mixture, a blocked or clogged exhaust. Overheating from a dull chain usually isn’t enough to cause serious damage to the chainsaw on its own. Never cut trees too big for your chainsaw as it can cause overheating and other serious issues.
Depending on how dull the chain is, this can even cause the chainsaw to overheat due to the huge amount of force it needs to put out all the time. To prevent dust from getting into the engine, chainsaws have an air filter installed. Most chainsaws use the 1:50 oil/fuel ratio, but always check your user manual for the ratio recommended by the manufacturer.
why does my chainsaw overheat Related Question:
How do you stop a chainsaw from overheating?
To prevent chainsaws from overheating they must be cleaned regularly. The cylinder and starter both contain air intake areas that pull cool outside air into the engine when it’s running. If dust, wood chips or other material blocks these systems, the engine will start to overheat.
What does it mean when your chainsaw smokes?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Is it normal for a chainsaw bar to get hot?
Over regular use, your rakers do decay a lot, and that eventually leads to heat buildup or similar issues on the chainsaw. Eventually, the chainsaw bar can be a passive source of heat buildup from improper raker height. So, the chainsaw raker depth must be accurate in order to reduce any type of overheating.
Why is my chainsaw blowing white?
Why is my chainsaw blowing white? While black smoke is caused by the burning of more fuel than air, blue or white smoke is generally caused by the burning of excess oil.
What causes white smoke from a chainsaw?
Smoke from a bad oil-gasoline mixture The main reason for a chainsaw that emits smoke (white most of the time), is the result of a bad oil / fuel mixture or bad oil. The oil / fuel mixture is to be prepared carefully, taking into account specific percentages.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
How often should you sharpen a chainsaw?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
How often should you flip the bar on a chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
How often should a chainsaw chain be replaced?
The chain sprocket must be replaced if the depth of the wear marks reaches about 0.5mm, i.e. the wear limit. A seriously worn chain sprocket can cause the chainsaw chain and guide bar to wear at an increased rate, as well as reducing cutting performance too, so it’s important to keep an eye on.
How long should a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
Will cutting wet wood dull a chainsaw?
Does Cutting Wet Wood Dull a Chainsaw? Using your chainsaw to cut through wet wood will not dull the chain any faster than using it for other types of wood. When you think about it, your chainsaw chain is already wet. True, it is not wet with water.
Why does my chainsaw chain dull so quickly?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.