The power behind a chainsaw provides almost everything you need to guide and control your cut, with very little effort on your part other than keeping it steady and providing enough pressure for the chain to its job. When you feel as if your cuts are taking much longer than they should, or you find yourself exerting much more force behind the chain than what you consider normal, you may want to look into why your chainsaw is not cutting in the manner it is designed to. If your chain is spinning, but not cutting, or the chainsaw is not cutting straight, then you need to address the chain itself- as I will explain in more detail below.
Take the guess work out of your repairs with our Fix app. Tap to download and it’s as easy as snapping a photo to find repair parts guaranteed to fit.
You might have noticed that your chainsaw stopping cutting halfway through. Another potential cause of your chainsaw stopping a cut halfway through is your chain being too tight. These are the most common causes of a chainsaw stopping cutting halfway through, and the less common ones tend to be costly to fix.
why does my chainsaw stop cutting Related Question:
Why does my chainsaw keep jamming?
Here are our explanations! Indeed, whether it is a chainsaw electric ou thermal, it is the teeth of its links that come into direct contact with the wood and the materials to be cut. As a result, dirt, wear on the guide or links and even the motor can be the cause of jamming.
Why does my electric chainsaw keep stopping?
If your electric or gas saw’s chain won’t turn around the bar, chances are that the chain brake is stuck. On some saws, resetting the chain brake is as simple as pushing in on the side cover of the saw’s body with one hand, and pushing the chain brake forward while grabbing the top handle with the other.
Should a chainsaw chain move freely?
The chainsaw chain should feel snug but still pull freely. Finally, perform a “snap” test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it.
What happens if you file rakers too low?
If you take your rakers down too low, on the other hand, your chain gets very aggressive and either stalls out in the cut or (worst case scenario), hangs up in the cut and kicks back at you.
Why does my chainsaw chain dull so quickly?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
How do you troubleshoot an electric chainsaw?
Charge the chainsaw if it is not turning on. If it has a battery, the battery may be faulty and require replacement. If it won’t start even when the saw is plugged into a power source, the battery is not the likely culprit. Replace the fuse in the chainsaw if it is still not starting and the battery appears healthy.
How often should you change the bar on a chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
When should you throw away a chainsaw chain?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
How do I stop my chainsaw from pinching?
To prevent the trunk from splitting it is advised to make a cut a third of the trunk’s diameter. This cut should be made on the side of the trunk that is going to be exposed to the most compression. This area of compression is also where the chainsaw’s bar will most likely become pinched.
What does a clutch do on a chainsaw?
The clutch allows the engine to turn freely at low rpm [rpm=revolutions (turns) per minute] without moving the chain. They are separate. Unlike a four wheeler or truck, the chainsaw operator doesn’t have to engage the clutch or put the chainsaw in gear.
How do you know if your chainsaw clutch is bad?
Does the engine loose revs, or the engine keep revving and just the chain stops? If the engine is still running at normal revs, and the chain slows down, then it’s a problem with the clutch. Worn out, gummed up, jammed springs etc. If the engine looses revs under load then it’s more likely a fuel or carb problem.
Why does my chainsaw pull to the left?
One major reason a chainsaw curves to either the right or left during a cut is that it was unevenly sharpened. The unequal teeth of the chain cause it to take a different-sized bite into the wood. What is this? The uneven sharpness of the chain is mainly due to manual sharpening, especially with the use of a file.
How high should the rakers be on a chainsaw chain?
The raker should be about 0.50. 8 mm lower than the cutter. You sharpen the cutters first. Lay the file gauge on the chain.
Why does my chainsaw cut curves?
Two main reasons will cause the chain to cut on a curve. The most common reason is from improper hand filing. If one side of the teeth is more heavily damaged, sharpening them down will make them smaller than the other side.