The armature is the central part of your belt sander’s motor. b. On the side of the sander with the belt cover; remove the three upper screws securing the two halves of the motor housing. a. Before joining the two halves of the motor housing, take note of the following: The bearing on the inside of the motor housing should align with the armature shaft; the plastic air guide must be aligned with the mounting holes; and the alignment pin should be visible on the front side of the motor housing.
why is my belt sander smoking Related Question:
When using a belt sander you should never?
1. Do Not use the belt & disc sander if you are too tired, hungry, sad, mad, or dehydrated. Never work while under the influence of drugs, alcohol, or any medication that creates drowsiness or impaired thinking.
Why is my belt sander squeaking?
The drum on a belt sander rotates on a set of bearings. Considering how fast the sanding belt moves, it’s amazing that these bearings last as long as they do. Eventually, they will fail, and you’ll probably hear a loud squeaking noise when you try to use your sander.
How tight should a sanding belt be?
Most wood sanding applications require a belt tension near 40 psi. Because the goal is to keep the belt from slipping, users sometimes err on the side of using too much belt tension. Several problems can result from excessive belt tension.
How much weight should you apply to the belt sander while sanding?
No need to lean on the sander. Just let the weight of the machine do the work. When you get to the end of the board make sure the platen doesn’t cantilever too far past the edge. Allow 1/3 or less of the platen length to project over the edge.
What are the 3 most important sander safety rules?
Safety Rules Dust mask advised. Don’t wear loose clothing or gloves, keep long hair tied back. Never adjust Sander or setup while Sander is running. Never remove guard unless authorized by Technician or WRL Manager • Setups requiring anything other than the standard sander equipment must be approved by supervisor.
Why does my Sander overheat?
There could be a few reasons for this problem. It may be that you are pushing down on your tool with too much pressure while sanding, increasing internal heat in the brushless motor, thus heat radiates out through the composite/grip housing to your hand.
Why did my Sander stopped working?
In most cases, a motor problem will prevent the sander from running, so if your electric orbital sander stops spinning completely, it might not have a working motor. You should be able to make the sander run again by disassembling it and replacing the motor.
Should I use gloves on belt sander?
Never wear gloves when using a belt sander. Many work gloves do not always fit tightly. This creates a situation where the gloves can actually become caught in the sander. You should always wear protection for your ears when using any type of power tool.
Do belt sanders need guards?
The belt guards and motor cover need to be in place and need to be secure before starting the machine. The gap between the sanding belt and the table cannot exceed 1/8” 13 SAFETY PRECAUTIONS II ● Keep machine clear of Excessive dust. Dust is flammable and potentially explosive.
How do you adjust the tension on a belt sander?
If the belt is shifting toward the side of the sander that the knob is on, then loosen the knob by turning it about half a turn counterclockwise. If the belt is shifting away from the side of the sander that the knob is on, tighten the knob by turning it about half a turn clockwise.
What size belt do I need for my belt sander?
Take a piece of string and wrap it around the sander as you would the sanding belt. Cut the string where it meets then measure the length of the string. This is your belt size.
When changing sanding belts or discs what should be done to the belt disc sander?
When changing sanding belts or discs, what should be done to the belt/disc sander? Disconnect the machine from the electrical service. On most disc sanders the table can be adjusted ___________ degrees. 45.
What position should the belt sander be positioned to sand edges?
For surface sanding using the stationary belt sander, place the table in a horizontal position. Curves can be sanded on the open end of a stationary belt sander when the table is in a horizontal position.
What may happen if you use too much pressure on the sanders?
Avoid pushing down with too much pressure on the sander. However, doing this can cause issues like swirls, cut-through, uneven sanding and other problems, such as excess heat and loading.
Why is my electric sander smoking?
Sawdust or other particles that frequently fly through the air in heavy work areas can get into your tool’s vent and cause that sparking or smoking. If your tool is free of burning debris, you may need to take apart the tool’s casing and check for heat damage.