If you use it too much while it’s overheating, it’s possible you may burn out the engine or pistons causing you to have a broken chainsaw that will either need to be repaired or replaced. Chainsaws generally cut out after starting because the engine gets too little or too much fuel from the carburetor. The most common problems why a chainsaw does not stay running are: Spark Switch/Plugs.
High/Low carburetor adjustment and Idle screws allow the proper airflow through the engine. No matter whether you set this too high or too low- it will cause the engine to die at idle. The simplicity of a 2 cycle engine makes it fairly easy to diagnose and solve the problems you may experience when working with your chainsaw.
why is my chainsaw cutting out Related Question:
How do you fix a chainsaw that won’t stay running?
Clogged Air Filter – Check the air filter Your chainsaw’s engine needs the right supply of air to run properly. A clogged air filter can be the reason why your chainsaw won’t start or stay running. Find your chainsaw’s air filter and remove it. If it’s clogged or too dirty, wash it or replace it.
Why does my chainsaw stop when I give it gas?
If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
Why does my chainsaw stall out when idling?
An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw stalls while it’s idling, adjusting the idle screw, which usually is marked LA, should help.
How do I know if my chainsaw carburetor is bad?
To test the carburetor, remove the air filter, pour a teaspoon of fuel into it, and pull the starter rope. If the engine starts momentarily and then dies, the carburetor is likely why the chainsaw won’t start.
Why does my chainsaw bog down at full throttle?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
Can you clean a chainsaw carburetor without taking it apart?
To clean a carb, you have to take it apart. If it needs cleaning, the parts that need cleaning can’t be seen from the outside.
How do you clean a carburetor without removing it?
To clean a motorcycle carburetor without removing it, you’ll need to remove the bowls at the bottom of the carburetor. Once the bowls are removed, spray some carburetor cleaner up inside, wait a few minutes, then spray again to ensure coverage. Then replace the bowls and start the motorcycle to assess how it runs.
How do you clean a 2 stroke carburetor without removing it?
Vacuum away any loose dirt, dust, debris, grime, and great on the surface with a handheld and cordless vacuum. Lay out rags or cloths at the base of the carburetor to catch runoffs and protect the surfaces. Apply the carburetor and choke cleaner in thin, even coats. Then, wait for it to settle and work its magic.
How do you start a stubborn chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
Why does my chainsaw bog down when cutting wood?
The reason for that may be you’re using the saw at altitude or the carburetor adjustment has simply slipped. The saw also won’t operate well at speed if the air filter or spark arrestor or carburetor are dirty.
Why does my engine bog down when I give it gas?
When you go to wide open throttle, the “Bog” simply means that the engine is not receiving enough fuel. It is possible for other issues to cause similar reactions within the carburetor, but often the problem is caused by the accelerator pump. An incorrect adjustment is the most common cause.
Can you clean a chainsaw fuel filter?
Brush the air filter gently with a soft brush or wash it in warm soapy water then dry it. Do not use compressed air to clean it – compressed air can blow holes in the filter, allowing dust and debris into your carburetor.
Can you spray carb cleaner in chainsaw?
You can use Sea Foam Spray to clean your chainsaw carburetor effectively. Sea Foam spray has a petroleum cleansing solvency. And adds lubricity to various components of the carburetor. It is a fine cleaning agent for chainsaw carburetors.
Why does my chainsaw dies when I turn it sideways?
Because the fuel covers the jets. When the bar points down or the saw is held sideways the jets no longer have fuel to cover them, it is air. The saw then runs lean and dies.
Is Sea Foam safe for chainsaws?
At Sea Foam, we recommend overcoming saw starting issues by adding 2–4 ounces of Sea Foam Motor Treatment to a low tank of fuel, running it for about five minutes, then letting it sit a night or two to soak or clean. Add fresh fuel and proper two-stroke oil before operating and it’ll be good to go.