Generally, a fully functional chainsaw should cut straight and smooth, but if this does not happen, your chainsaw is likely to be faulty. The chainsaw bar can cause the chainsaw not to cut woods straight. The first step to solving any chainsaw problem is to understand the type of chainsaw suitable for your needs and how it operates.
Dull cutters damaged by rocks can cause a chain to cut crooked. It’s important to remove all damage from cutters prior to cutting. Cutting with a dull chain can accelerate wear to the bar and chain.
When the saw teeth become chipped, damaged or dull, the chainsaw likely won’t cut straight, especially if more teeth are affected along one side of the chain. Sharpen the teeth uniformly using a file and file guide, or take it to professional for sharpening. Madsen’s recommends using a grinder rather than a file, if you want to avoid taking it to a professional.
The most probable reason why a chainsaw pulls either to the right or left during a cut is because it was sharpened unevenly. Keep working the side which you feel lacks attention, and eventually the chainsaw should start going as straight as new. The teeth have to be equally sharp on each end to make the chainsaw work straight.
why is my chainsaw pulling to the right Related Question:
How do I stop my chainsaw from cutting crooked?
Check the size of the top plates, which sit on the longer sections of each tooth on the chain. These top plates should be the same size. If some are shorter than others, file the longer ones down to match. Keep the same angle on all the top plates as you file – angles that don’t match also can cause curved cutting.
What would make a chainsaw cut crooked?
Uneven top plates can cause a chain to cut crooked. It’s important to keep all top plates equal length. Dull cutters damaged by rocks can cause a chain to cut crooked. It’s important to remove all damage from cutters prior to cutting.
Why does my chainsaw bog down when cutting?
The reason for that may be you’re using the saw at altitude or the carburetor adjustment has simply slipped. The saw also won’t operate well at speed if the air filter or spark arrestor or carburetor are dirty.
Why is my chainsaw bar smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
Why does my chainsaw rev too high?
The throttle valve (butterfly) simply cuts off the supply of combustible air/fuel and the engine stops. If this adjustment is set too high, the high idle speed will cause the centrifugal clutch to engage and the chain will run. This is a dangerous condition and should never be allowed.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
Why do chainsaw chains stretch?
A chainsaw chain stretches and loosens from tension and extreme friction. The friction from cutting through wood makes the chain very hot and the heat causes it to loosen. The heat expands the guide bar and when it cools, the chain has stretched. The chain will also loosen as it wears down from use.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Do you flip the bar on a chainsaw?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
Why does my chainsaw dull so fast?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
Why is my chainsaw blowing white?
Why is my chainsaw blowing white? While black smoke is caused by the burning of more fuel than air, blue or white smoke is generally caused by the burning of excess oil.
Why does my chainsaw bar get so hot?
If your chainsaw’s blade is overheating and producing smoke, it means that there is a serious problem with it. In that case, you must start troubleshooting at once. The two most common causes of the overheating or smoking of your blade are lack of lubrication of the bar guide or the engine and lack of air.
How many times can you sharpen chainsaw chain?
Cutters can be sharpened up to 10 times or more before the chain needs replacing. If your cutters are worn unevenly after a few sharpenings, a professional can regrind them to uniform shape. If you use the same chain for a few years, then buy a new one, the new one won’t mesh smoothly with the sprocket and bar.