The power behind a chainsaw provides almost everything you need to guide and control your cut, with very little effort on your part other than keeping it steady and providing enough pressure for the chain to its job. When you feel as if your cuts are taking much longer than they should, or you find yourself exerting much more force behind the chain than what you consider normal, you may want to look into why your chainsaw is not cutting in the manner it is designed to. If your chain is spinning, but not cutting, or the chainsaw is not cutting straight, then you need to address the chain itself- as I will explain in more detail below.
Chain tension can definitely stall your chainsaw’s ability to cut correctly, even with a sharp chain. No matter how precise your chain tension is or how sharp the cutting teeth are, if your chainsaw’s chain isn’t mounted correctly, it isn’t going to cut anything. If there is no need to replace the bar on your chainsaw and you feel confident in your cutting teeth sharpening skills, chain placement, and chain tension, you need to keep reading!
Take the guess work out of your repairs with our Fix app. Tap to download and it’s as easy as snapping a photo to find repair parts guaranteed to fit.
The common chainsaw includes a body, a 2-cycle engine, a gas tank, handles, a guide bar, a clutch and chain that fit around the bar. As the chainsaw is running the chain or teeth rotates around the guide bar at high speed, which permits the teeth to cut through wood. If the chain is too tight or loose, adjust it by loosening the nuts that hold the bar in place, then tighten or loosen the bar’s adjustment screw as necessary and then re-tighten the guide bar nuts.
why my chainsaw won’t cut Related Question:
Why does my chainsaw not want to cut?
The most common cause of a chainsaw that won’t cut properly is a dull cutting chain. Try sharpening or replacing the chain. The chain may not have the proper amount of tension. If the adjustment screw is too loose, the chain may not make good contact with the wood.
Why does my chainsaw smoke and not cut?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Why does my chainsaw blade not turn?
The chain tension may be too tight. Easy fix, just loosen the bar-retaining nuts and rotate the tensioning screw counterclockwise to the correct tension. Then tighten the nuts back up.
Why does my chainsaw stick?
Chain tension Indeed, if a chainsaw chain that slackens with wear no longer cuts, it damages the guide, tires the engine and can be the cause of a blockage when it is too tight. In addition, the more the chain saw heats up, the more the tension of the links decreases, until they become too relaxed.
How long should a chainsaw blade last?
The lifetime of a chainsaw chain has no fixed limit and depends on usage and maintenance. The chain should last many years; 5-6 years should be no problem. However, if the chainsaw chain is used properly and taken care of, it can last way longer.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
How long do chainsaws stay sharp?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
How do you start a stubborn chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
Can I use wd40 on my chainsaw?
We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.
How do I know if I need a new chainsaw chain?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
Why does my chainsaw go blunt so quickly?
What is this? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast. It won’t be hard to notice whether the wood that you’re cutting is dirty or not.
Is it worth sharpening a chainsaw?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How do I know if my chainsaw oil pump is bad?
Generally speaking, the signs of a chainsaw oiler problem are easily spotted. If the chainsaw seems like it’s getting too hot or producing smoke, that is a sign that there is an oil deficiency in the chain. This is not good for the life of your chainsaw. If you spot this problem, it is time to troubleshoot the issue.
How often should you flip the bar on a chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.