Let’s take a look at some of the most common issues that can come up when your chainsaw is hard to pull and the simple steps you can use to fix it. If the spring or pulley is damaged, the chainsaw cannot start and it will either feel too easy or too hard to pull. Often the chainsaw will start to fail and is hard to pull because it gets old and a part breaks.
The starter assembly rotates when the starter rope is pulled. If the engine fails to fire-up after pulling the rope, you have to wait for the rope to retract before trying again. Is your chainsaw suffering from a hard pull? Simply check the damaged part of the starter assembly and repair or replace it. Damaged rope can cause other parts of the starter assembly to damage; hence; it is very pertinent to replace the rope immediately. You can prevent the new starter rope from fraying by burning the two ends of the rope. 5. Fix the rope such that the pulley rotates a little more than half turn whenever the rope undergoes maximum extension. Keep the rope securely in place by tying another knot on the rope.
Exposure to moisture could cause a chainsaw to rust, and this could make it hard to start the chainsaw. If you store your chainsaw in a place that isn’t good for it, then you’ll be more likely to have the chainsaw rust over time and parts of the chainsaw might get gummed up. Yes, sometimes chainsaws can get hard to pull due to getting older, and it might not always be the best decision to make to keep trying to fix the chainsaw.
One smart pull on the starter should get the saw started now. Some of these high compressing saws take a good firm pull to get started, a little too slow and they will kick back and jerk the cord out of your hand. For my own peace of mind, if it was my saw, I would find another dealer and get it checked over.
why won’t my chainsaw pull start Related Question:
What makes a chainsaw hard to start?
A fuel issue is one of the most common reasons why a chainsaw won’t start. If the operator has repeatedly been trying to start the chainsaw through the recoil starter system, they may have accidentally flooded the engine with fuel. A common indication the engine has been flooded is the smell of gasoline in the air.
Why is my pull cord hard?
The problem may be in the recoil starter itself. A tangled coil of rope or a broken spring may be the problem. In many cases the recoil starter is easily replaced as a single assembly. DO NOT attempt do take the starter apart.
Can you start a chainsaw without a pull cord?
There are four different ways to start a chainsaw easier or without pulling the cord: you can also start your chainsaw with a drill. Spring-assisted starting system. Capacitor discharge ignition (CDI) or Memory power ignition (MPI)
Will a chainsaw run without a fuel filter?
While it’s possible to run your chainsaw without a fuel filter, but this is not recommended. When a fuel filter is clogged, it can cause considerable damage to the engine and leave your chainsaw unusable.
What causes small engine kickback?
Kickback is when you pull start your mower, and the pull cord is snapped from your hand. It can sometimes whip you as it does so, which is Oouch!!. A lawnmower engine commonly kicks back when the shear key breaks. The shear key commonly breaks because the blade has kit a solid object and come to a sudden stop.
How do I know if my chainsaw spark plug is bad?
If it’s not producing any sparks at all, your chainsaw needs a new plug. If there are only a few sparks coming out of one side of the electrodes but none on the other side, it’s not bad enough for you to worry about, but it will affect your performance.
Why is my Stihl chainsaw not starting?
Dirty or clogged fuel tanks, dirty fuel filters and lines, loose fuel hoses, dirty air filters and a dirty carburetor can all restrict fuel flow. Check, clean and replace all the fuel system parts before moving into the internal engine, as gas problems create a majority of starting problems.
How long does a spark plug last in a chainsaw?
A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.
How do you clean the carburetor on a chainsaw?
Let the chainsaw run at low RPMs/idle for a while. This is to let the cleaner run through the carburetor, the fuel lines, and the idle engine. The cleaner will wipe remove the gummy residue blocking the components to create a clean passageway for the air and fuel. As the RPMs begin to increase, turn down the idle knob.
Do you need to oil recoil springs?
Recoil spring doesn’t need to be oiled for functionality. However – whenever you use cleaning solvent on spring or rod – they have to be wiped with touch of oil, otherwise they are completely dry. (No need if you use CLP.) Once you put a little oil, just wiped it out with dry cloth or patch.
Do you start a chainsaw with the brake on?
When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.