If you need to cut workpieces that must be cleanly and accurately joined together, a circular saw and a guide rail is the way to get this done. Clean, accurate cuts over and over are possible when using a guide rail. The saw is also compatible with other makes of guide rail.
More than 80% of serious harm accidents concerning circular saws involve missing or poorly adjusted guards, or push sticks not being used. Figure 1: circular saw benches HazardsEntanglement from contact with blade. A safe noise level over an eight hour day is 85db. A circular saw may exceed this noise intensity.
how to use a circular saw nz Related Question:
How do you use a circular saw accurately?
Start With Accurate Marks A “V” is more accurate than a single line, which can stray slightly to the right or left and throw off your cut mark. Using a square, mark your cutting line over the tip of the “V.” Finally, put an “X” on the “scrap” side of the board; that’s the side of the line you want to cut along.
How do you use a circular saw without a table?
Fit your circular saw with an edge guide. Set the depth of the blade accurately enough for it to go through the wood and not cut under the surface. Place the guide on base of the circular saw lines and markings you made earlier on the wood. Ensure that the saw is free to move, and the power cord is not entangled.
Which side should the blade be on a circular saw?
For blade-right models, the correct circular saw blade direction is usually with the label side out. For saws that have the blade on the left, it typically installs with the “ugly” side out.
Why does my circular saw kickback?
Overheating a saw blade can cause it to warp and result in a kickback. Buildup of sap on the blades, insufficient set, dullness and unguided cuts, can all cause an overheated blade and kickback. Never set a blade deeper than is required to cut the work piece 1/8 in. to 1/4 in.
When using a circular saw be sure to cut on the waste side of the cut mark to allow for the blades?
Never use a circular saw that does not have an upper blade guard because the. guard protects you from touching the blade. When using a circular saw,be sure to cut on the waste side of the cut mark to allow of the blade’s. Saws with fine blades that are excellent for delicate and intricate cutting are called.
Why won’t my circular saw cut all the way through?
Here are some reasons your circular saw keeps stopping: Make sure your work piece is properly supported so it doesn’t pinch the blade which could also cause kickback in addition to stopping. Damaged, warped, loose or dull blade. Motor malfunctioning or overheating. Cable problems like frayed cord or weak connection.
Can you cut wet wood with a circular saw?
If you’re cutting wet wood set the depth so that the entire gap between the teeth is clear of the board you’re cutting. This will stop your saw and cut line from getting clogged with wet saw dust.
How do you cut straight with a circular saw without a guide?
To ensure a straight cut, press the saw firmly against the straightedge as you push it along. Clamp a perfectly straight board or metal straightedge to a sheet of plywood to make cabinet-quality straight cuts.
Can a circular saw cut a 4×4?
Circular Saw. A circular saw is one of the best means of cutting a 4×4 post. Most people own a circular saw, its portability makes it easy to cut 4x4s from the ground, and they can make precision cuts by using a relatively simple trick.
Why is my circular saw burning the wood?
Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty. If wood pitch resins build up behind the teeth of the blade, the cutting speed will slow down, increasing the chances for burns. Commercial blade cleaners are sold for this purpose.
What is the difference between a circular saw and a table saw?
Circular saws are lightweight, hand-held, and can be moved from jobsite-to-jobsite with ease. A table saw is heavier and more complex in its set up. Because of its weight and footprint, this tool is more difficult to move these saws around as easily as you are able to do with a circular saw.
What size circular saw Do I need to cut 2×4?
You need a minimum 5-3/8 inch size circular saw blade to cut a 2X4 at a 90 degree angle in one cut which is a crosscut. If you want to cut a 45 degree bevel with this size circular saw it will take 2 cuts. You could go with a 7-1/4inch or 10 inch blade to avoid making multiple cuts with the 45 degree bevel angle.
Why do some circular saws have the blade on the left?
Traditionally, all worm drive saws operated in a blade-left orientation. Furthermore, this orientation likely places the weight of the saw over the portion of the material the user wants to keep, making it easier to stabilize the saw during the cut.
Why are so many circular saws left-handed?
The placement of the cordless saw blade, on the left side, gives you a clearer line of sight when you cut. The reason for this is because the main bulk of your circular saw is not blocking your view. Cordless circular left-handed saws provide you better movability.
Can a circular saw blade break?
Making sure your saw blade is working properly is the best way to reduce downtime and increase production. There are many common causes that can cause blade failure from blade selection to cutting speeds, feed rates and improper break-in, to maintenance problems and more.
