You will hear both sides, some say yes it will hurt the saw some say no it wont. To tell you the truth I have seen some saws with such huge muffler mods they basically were running with no muffler and i have saw a few with a straight pipe no muffler just a inch pipe, that was on some old macs, they seemed to run fine. Just me if it were my saw i would not run it with an open exhaust port, I would get a muffler.
will chainsaw run without muffler Related Question:
What does a muffler do on a chainsaw?
Function. The muffler serves the purpose of reducing noise while the chain saw is in use. It also pushes exhaust from the chain saw operator, reducing the amount of exhaust the operator inhales.
What temperature does a chainsaw muffler get to?
If you own a chainsaw, you can get upwards of 200 degrees using a chainsaw muffler. The heat of a car’s muffler, a few feet from the engine, can push the boiling point to 212 degrees.
Can I run a chainsaw without clutch?
A clutch is an absolute necessity on a chainsaw. Without one, the chain sprocket would be connected directly to the motor, and the chain would turn even when the engine is idling.
How can I improve my chainsaw performance?
Chainsaws can be modified to boost their performance and increase power. The basic idea is to increase the airflow through the engine. The most common method is muffler modification. This involves widening the muffler’s exhaust ports to improve the airflow at the exhaust.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Why do chainsaws have clutches?
The clutch allows the engine to turn freely at low rpm [rpm=revolutions (turns) per minute] without moving the chain. They are separate. Unlike a four wheeler or truck, the chainsaw operator doesn’t have to engage the clutch or put the chainsaw in gear.
Can I start my chainsaw without bar?
Running a chainsaw without bar oil will cause mechanical problems, and some serious safety issues, such as: Kickback. Chain failure. Dulls the chain.
Why does my chainsaw chain get dull so fast?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
What is the advantage of a skip tooth chain?
A skip chain has fewer cutting teeth than a conventional chain which means it won’t be dragging as many teeth through the wood you’re cutting. Less drag on the chain means less power is needed to cut through the log. That means the motor on your saw runs faster which keeps it in a more efficient power curve.
What is Woods porting a chainsaw?
They typically include: opening up the muffler (by grinding, drilling, or adding factory port options), opening up the intake and exhaust ports (by grinding and polishing), lowering the jug by milling or using thin/no gasket to raise the compression (called squish), turning down the piston around the top edge to allow
How do I get more torque out of my chainsaw?
My opinion the only proper way to get more torque out of a chainsaw, is to lower the “gear ratio” at the drive sprocket. That is run a smaller drive sprocket. Back in the day gear transmissions were a very reliable way of producing extra torque. .. Making a living with a saw since age 16.
What are chainsaw mufflers made of?
Re: what type of metal is a 026 muffler made out of It is steel.
What is exhaust muffler modification?
The exhaust mods can improve your car exhaust with custom the performance of the exhaust system, by that allows the entire engine to function better. It can be explained by the relation between the exhaust and the engine. Changing exhaust allows a quicker, more efficient path for exhaust gases to escape.
What chainsaw do loggers use?
Stihl is the most popular chainsaw for professional loggers. It has a long-lasting chain, and you can also enjoy the exceptional cutting speeds available with this brand of chainsaw. Additionally, the chains are high-performance, low vibration, and quiet in their performance.
What is the biggest chainsaw made?
For the largest, toughest and most demanding jobs, professionals can find the performance they need in the MS 881 chainsaw. With its updated engine design and up to 41” guide bar length, the MS 881 is the largest, most powerful saw in the STIHL lineup.