Check and replace bar and chain oil regularly to reduce friction, keep the saw from wearing out faster, and to make cutting easier. Be sure to use bar and chain oil, Not regular motor oil. Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
I usually go through 4 to 6 gallons on an average year, doing the tree removal thing…….I buy by the gallon as well. In the winter I used to use several quarts of 30wt. oil, but I’m going to give canola oil a try, especially if I ever get a mill for my big saws. That’s when you will see the oil consumption go WAY UP…..
Every time you refuel your saw you should be topping up your chain oil. A lot of chainsaws are equipped with an adjustable oil pump to increase/ decrease the amount of oil getting onto your cutting equipment. Chainsaw manufactures generally design oil tank size so that you use one tank of fuel mix to one tank of oil.
how much chainsaw oil do i need Related Question:
How much oil do I put in a 2 stroke chainsaw?
Most modern day chainsaws get best performance from a 50:1 fuel mix ratio – that is 2% oil or 20ml of quality two stroke oil per 1 litre of fuel. Some larger capacity saws over 65cc may require a 33:1 (30ml of oil per 1 ltr of fuel) or even 25:1 (40ml per 1 ltr).
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can I use 5w 30 for bar oil?
Can I Use 5w30 for a Chainsaw Bar? Like 10w30 motor oil, you can use 5w30 oil. However, the thin and low-viscosity SAE5 weight oil will not cling to the chain and chainsaw bar very well in the summer. You may experience a lot of oil loss and a messy worksite if you choose this chainsaw bar oil alternative.
How often do you oil a chainsaw chain?
The chain saw should be oiled before each cut. For Manual Oiling System: Lubricate the saw chain by pressing the bulb on the oil reservoir cap twice before making each cut. Hold the bulb down for 3-4 seconds on each press. Automatic oiling system will keep the bar and chain constantly lubricated.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
When should I oil my chainsaw?
So, whenever you refuel your gas chainsaw, you should add bar and chain oil as well, every time. The steps are quick and easy: Set your chainsaw on a level surface, bar side down so that it lays flat. Allow a minute for the oil to settle, then unscrew the cap to the saw’s bar and chain oil reservoir.
How much oil do you put in a petrol chainsaw?
The general ratio for most two-stroke chain saw combustion engines is 50:1, though some manufacturers recommend 40:1. The larger number represents the amount of gasoline, while the smaller is the amount of oil needed.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Can I use 2 stroke oil for chainsaw?
Modern two stroke chainsaws do not require generic brand oils to operate at temperatures and rpms that are comparable to those of generic brand oils. Our recommendation is to use only high quality two stroke oil designed for air cooled high performance engines when using your modern two-cycle engine.
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
What kind of fuel does a chainsaw use?
Unleaded gasoline with a minimum octane rating of 89 is recommended. A lower octane can cause some issues, such as increased engine temperature, increased piston seizures, and engine damage. Stihl offers 2-cycle oils made especially for Stihl chainsaws. Premium quality 2-cycle fuels provide protection for your engine.
How much oil do you mix with 2 gallons of gas?
If you’re mixing up two gallons of gasoline you will have to mix 5.2 ounces of oil to two gallons of gasoline for a 50:1 mixture. I would recommend using fresh gasoline that has an octane rating of 89. Remember, 2.6 ounces for one gallon and 5.2 ounces for two gallons of fresh gasoline for a 50:1 mixture.
Can I use 5w20 instead of bar and chain oil?
They are 5w20 and 10w30, which would be best? You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden!
Can you use 5w20 for bar and chain oil?
Yes and no. Never use waste motor oil in anything. You can use fresh motor oil in a pinch but regular bar and chain oil has special additives to make the oil cling to the bar and chain.
Why is my chainsaw using so much oil?
What causes a chainsaw to leak oil? As the oil is pumped from the tank through to the guide bar, air begins to replace the space where the oil was previously stored. If there isn’t proper ventilation of the oil tank, a vacuum can occur and reduce the flow of oil to the guide bar.