Knowing how to properly clean it is a key component of chainsaw care. Wipe the chainsaw housing clean with a damp cloth. Once you have emptied the fuel tank, start up the chainsaw and allow it to run idle for a short time until there is no more petrol in the fuel system and the chainsaw switches off.
Below, I’ll teach you how to clean a chainsaw so it looks spotless and runs like new again. As for cleaning the chainsaw guide bar groove, you can either use a special groove cleaning tool or a putty knife. I hope you enjoyed this post on how to clean a chainsaw.
Some of the sawdust and wooden chips also get flung into the spaces in-between each chain link, combining with moisture and bar oil to form a semi- solid and highly sticky substance that soaks up new bar oil and prevents it from lubricating the chain. Now, located the two nuts on the side cover which keep your bar mounted to the powerhead. Loosen these nuts from the bar studs using the hexagonal wrench part of the scrench, and make sure that the anti- kickback chain brake is disengaged before you remove the clutch cover. Using the bar groove cleaner tool or a putty knife, clear out all the gunk that is stuck within the bar rails.
This video shows how you can quickly clean your chainsaw using compressed air. Here’s another video showing how to clean and maintain a chainsaw. A chainsaw doesn’t always need a full thorough clean every time as demonstrated in this video.
how to clean stihl chainsaw after use Related Question:
How do you clean a Stihl chainsaw after use?
To clean then properly, first remove the saw chain and the guide bar. Remove oil residue and dirt from the oil outlet port and channel, then clean the oil inlet hole and the bar groove; you can use a filing gauge for this, or STIHL’s SuperClean resin solvent is also very effective.
How do you clean a chainsaw after each use?
In a well-ventilated area, take a bucket and mix one cup of ammonia with one gallon of water. Place the chainsaw chain in this solution and let it soak for 15 minutes. Put on a pair of thick rubber gloves for protection. Then, use a soft-bristled toothbrush to scrub each section of the chain until it’s free of debris.
What can I spray my chainsaw with to clean?
To clean the bar, you should add some degreaser or lubricant such as WD-40® Multi-Use Product, mixed with warm water. Once soaked with the solution, use a rag to remove all the dust and grease. If there is stubborn grime, you can use a wire brush to remove it.
Should I empty my chainsaw after use?
Never run your chainsaw dry, instead use a quality gas stabilizer. A stabilizer will keep fuel fresh and protect a chainsaw fuel system from damage caused by stale gas.
How do I clean the oil tank on my Stihl chainsaw?
Half fill the tank, close, slosh around, leave sit a while, slosh some more and empty – repeat a few times. Then retrieve the filter line with a hooked wire, change filter, fill with white spirits again and run the saw a while to flush the chanells and pump.
Can I clean my chainsaw with brake cleaner?
Can I Use Brake Cleaner To Clean My Chainsaw? If you are washing parts that are covered in oil, you should never use water on them. Instead, use carb or brake cleaner to blow out the dirt and oil more effectively.
How often should I clean chainsaw?
For homeowners, this means you’ll need to clean your filter twice a year on average. Professionals may need to do it weekly, and sometimes even more frequently. The best time to clean or replace the air filter on a chainsaw for most people is at the start of the cutting season.
Is it OK to leave gas in chainsaw?
To store your chainsaw, do not run it out of gas for the winter. This allows the interior seals to dry (and possibly crack) and that is very bad for your saw.
How long does gas last in a chainsaw?
What is the runtime of a Chainsaw? Depending on the type and usage, you can expect a gas Chainsaw to run between 15 and 40 min before you have to fill it up again. Most battery-powered chainsaws have a run time of up to 2 hours, but there are high-capacity power packs that will last much longer.
Why is my chainsaw using so much oil?
What causes a chainsaw to leak oil? As the oil is pumped from the tank through to the guide bar, air begins to replace the space where the oil was previously stored. If there isn’t proper ventilation of the oil tank, a vacuum can occur and reduce the flow of oil to the guide bar.
How often should you change the spark plug in a chainsaw?
A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.
How do you clean a chainsaw without a compressor?
Make a solution using a gallon of water and a cup of household ammonia and soak these parts in the solution for 20 minutes. Once the soaking time is over, take them out and scrub using a stiff brush. Rinse them thoroughly using warm water.
How much does it cost to have a chainsaw chain sharpened?
A typical chainsaw can be sharpened up to 10 times before it’s time for a replacement. The cost to have a chainsaw sharpened ranges from $13 to $16. The average cost per chainsaw sharpening is $14.50 for people who choose to have their chainsaws professionally sharpened.