Learning how to prevent your chainsaw from pinching when you’re cutting firewood is something everyone should understand. There are two easy techniques I like to use to prevent a chainsaw from pinching when the tree or tree top is already on the ground and you’re ready to cut it up into firewood sized pieces. Placing small pieces of firewood under the tree or using wedges are two easy ways to prevent your chainsaw from pinching when you’re cutting up a tree for firewood that’s already on the ground.
Laziness has resulted in my chain and bar getting pinched in the compression side of a log on more occasions than I like to admit. More often than not, I get my blade and chain caught while trying to cut through a large log. I am down on one knee, the saw is cutting like through butter, and I just don’t want to stop and pound a wedge into the top of the cut to keep it from closing on my saw.
Imagine someone doing a split, where one leg is the tree trunk, the other is the roots that are still going into the ground, and you’re gonna kick that first leg out. 2) Rig the roots/stump to another tree or something solid so that you are applying tension away from the side you will be standing on. 5) The bottom side of the trunk should be in tension and the top side in compression.
how to prevent chainsaw pinching Related Question:
How do I stop my chainsaw from pinching?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
How do you cut down a tree without a pinching chainsaw?
Placing small pieces of firewood under the tree or using wedges are two easy ways to prevent your chainsaw from pinching when you’re cutting up a tree for firewood that’s already on the ground.
Can you fix a pinched chainsaw bar?
To open pinched rails, mount the bar in a vice and gently tap on the bent rail with a hammer and punch. A flat-blade screwdriver is another tool that can be useful for prying open bent bar rails. Once you’ve got the pinch worked out, test your repair by placing the chain back in the groove.
How do you cut a tree under tension?
A felled tree will usually have saw-pinching areas where the top of the log is under compression and the bottom is under tension. If you have access to the top and bottom of the log, you can handle this one of two ways. Make a cut directly down from the top and then finish by cutting up from the bottom.
Why does my chainsaw dull so fast?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
What should you not do when a tree falls off?
When cutting up a felled tree, avoid touching the ground with the chain because even a brief encounter will severely dull the cutting teeth on your chain saw. If possible, cut partially through the tree and then rotate it to cut the rest of the way through.
Does a chainsaw bar wear out?
As a chainsaw bar wears out, you’ll lose cutting accuracy and efficiency. If the same type of cuts that your saw used to breeze through are now taking twice as long, and you’re sure that your chain is sharp enough, you might look at how worn your bar has become. Thankfully, there are a few simple ways to check this.
How do you use bucking spikes?
Bumper Spikes: This series of sharp metal spikes protruding from the saw near the base of the bar provide leverage for easier, more controlled sawing. Jab the spikes into the log, then pivot the bar downward to guide the chain through the cut.
Do I cut compression or tension first?
Always cut on the compression side first! The area on the outside of the bend will pull apart when cut. This is the tension side. If you decide to cut this side only, the tree will split apart before the cut can be completed.
Do you start a chainsaw with the brake on?
When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
What is limbing a tree?
Limbing is the removal of the branches from either standing or downed trees. Bucking is the process of cutting the downed tree into appropriate lengths.
Why do loggers run upside down bars?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
Why should we not cut trees?
Ans. We should not cut trees because trees give us oxygen to breathe. Trees are also useful in many other things like, they give us fruits, vegetables, herbs and wood, etc.
What is Swedish cope?
Using natural tree-shaped logs, Swedish Coped logs are hand-scribed together with saddle notched corners offering a tight fit between logs and protection against the elements.
How big should log cabin be?
Logs should all be the same diameter. The minimum diameter is 8 inches, but most recommendations are for 10-12 inches. Once you have decided on a log size, we can then do some calculations. If your cabin is 20’x24′ and has 9′ walls then each wall will be 108″ (9×12).