Circular saws cut on the upward stroke, which means that they rotate in a clockwise fashion, cutting from the bottom up. This is why when you’re using a circular saw, the side of the wood that will be your “good” side should be facing down.
Most of us have been there at some pointstaring at a blade in one hand and a saw in the other wondering what the correct circular saw blade direction is. Getting the circular saw blade teeth going the correct direction is what’s at the heart of the matter. The saw’s motor runs the blade rotation in a way that the circular saw teeth direction points up as it enters the wood you’re cutting.
A circular saw blade spins upwards as it forces the wood to be held between the blade and the base of the circular saw. The teeth on your circular saw blade should point in an upward direction at the front of the saw. All circular saw blades spin in an upward direction with the teeth pointing up towards the base of the saw.
A challenge when determining the right direction for table saw teeth is that the saw conceals most of the blade, making it hard to see the teeth. Hand saw: If you’re using a non-motorized hand saw for cutting wood, the blade’s teeth should always point in a downward direction. If you’re not sure which direction the teeth on your saw blade should point, contact an expert on the team at Luxite Saw.
Unlike table saw blades that rotate clockwise, circular saw blades have been designed to spin in an anti-clockwise direction. Circular saw blade teeth always point up on the front side of the saw. When using circular saws, make sure that the blade points to the opposite direction of the table saw blades.
does a circular saw cut up or down Related Question:
Which way do circular saws cut?
When appearance matters, make cuts with the good side facing down, as circular saws can splinter the wood on the top side. Making your cut line on masking tape can reduce splintering.
Why do circular saws cut upwards?
The saw’s motor runs the blade rotation in a way that the circular saw teeth direction points up as it enters the wood you’re cutting. It’s intentional to create the most stable, accurate, and safe cutting. As the blade teeth hit the material, they rip from the bottom through the top.
Why do circular saws cut up instead of down?
The teeth of circular saw blades are intended to cut upwards into the material from below and this is for safety purposes. It is important that you should not spin them in a different direction just like you spin a table saw blade.
Can you use a circular saw upright?
It’s aggressive, makes straight vertical cuts and it’s fast. The circular saw outperforms the jigsaw and reciprocating saw for most straight cuts. It can be tricky to use in some situations, but the cuts tend to be straighter and more accurate than with almost any other portable saw.
Can you put a circular saw blade on backwards?
When cutting vinyl siding with a circular saw, install a fine-toothed blade backwards on the saw for a smoother, cleaner cut, especially in cold weather (when the material is brittle).
Is there a left and right handed circular saw?
Here’s a hint—it’s not by accident that manufacturers don’t call these “right-handed” and “left-handed” saws. Our Pros will tell you that it’s all about what you get used to and are comfortable with. In fact, most have both types of saws for different applications.
Can I use a jigsaw instead of a circular saw?
Although a jigsaw can be used for most of the tasks that a circular saw can perform, including straight cuts and cuts on a tilt, the jigsaw uses that really take advantage of the tool’s qualities are jobs such as kitchen fitting and joinery, with their frequent need for complex cuts.
Can you cut oak with a circular saw?
Straight cuts are best with a circ saw with a decent blade guided against a straight edge. I doubt you’ll cut 26mm Oak either straight or square with a jigsaw. Cut outs and scribes I’d do with a 1/2 inch bit in the 1/2 inch router running against a template made from 6mm MDF.
How do you cut straight with a circular saw without a guide?
To ensure a straight cut, press the saw firmly against the straightedge as you push it along. Clamp a perfectly straight board or metal straightedge to a sheet of plywood to make cabinet-quality straight cuts.
How do you use a circular saw without a table?
Fit your circular saw with an edge guide. Set the depth of the blade accurately enough for it to go through the wood and not cut under the surface. Place the guide on base of the circular saw lines and markings you made earlier on the wood. Ensure that the saw is free to move, and the power cord is not entangled.
Why is my circular saw burning the wood?
Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty. If wood pitch resins build up behind the teeth of the blade, the cutting speed will slow down, increasing the chances for burns. Commercial blade cleaners are sold for this purpose.
Why are most circular saws left-handed?
The placement of the cordless saw blade, on the left side, gives you a clearer line of sight when you cut. The reason for this is because the main bulk of your circular saw is not blocking your view. Cordless circular left-handed saws provide you better movability.
Which saw to get first?
A jigsaw is great for cutting curves and shapes, and it can also be used with a guide to make straight cuts, which is why this is the first power saw you should own. Unless you plan to rip long sheets of plywood, a jigsaw is preferable over a circular saw.
Which is better miter saw or circular saw?
A circular saw excels at breaking down sheet goods, and a miter saw is best for cutting down longer boards. A miter saw is more precise, due to the handheld nature of the circular saw. A circular saw is less expensive than a miter saw, and it’s more portable. A miter saw is safer to use than a circular saw.
What is the difference between a table saw and a circular saw?
Circular saws are lightweight, hand-held, and can be moved from jobsite-to-jobsite with ease. A table saw is heavier and more complex in its set up. Because of its weight and footprint, this tool is more difficult to move these saws around as easily as you are able to do with a circular saw.
