Malco’s Vinyl Cutting Circular Saw blades come in three different models, VCB1, VCB2EV, and VCB3EV. VCB1 – VERSATILE 7-1/4 INCH CIRCULAR SAW BLADE IS A MUST-HAVE FOR PORTABLE CIRCULAR SAWS. A popular blade choice when you need to go where the work is. Why settle for a make-do plywood blade when you can have the real thing in a flat-ground 186 tooth blade that offers smooth cutting in a range of vinyl plastics including vinyl fencing, siding and trim profiles. The large 10″ diameter provides a deeper, more efficient blade path for fast cuts in wide siding panels and more accurate single pass cuts in large profile vinyl fence posts.
The Freud D1280X Diablo features a 12″ diameter saw blade that you can use for cutting vinyl plank flooring. You have several ways to cut vinyl plank flooring, depending on what type of vinyl flooring you will cut. As mentioned above, you need to select with care the tool and the saw blade you will use to cut the vinyl plank flooring.
best circular saw blade for vinyl Related Question:
What saw blade is best for cutting vinyl?
Preferably use a circular saw with a PVC blade or a sharp and straight fine-tooth carbide blade. If your saw blade is designed for rough cutting lumber and dull, it could shatter the vinyl. This is especially true if the vinyl is cold.
What is the best circular saw blade for cutting vinyl siding?
Powered circular saws using a blade that’s mounted backward are known to provide the cleanest and easiest cuts for vinyl siding. For fine-toothed jigsaws, a 36 TPI rating will be sufficient for the job. A 36 TPI rating means the blade has 36 teeth per inch. Hacksaw blades should have a 32 TPI rating.
Can I cut vinyl siding with a circular saw?
If you need to cut a lot of vinyl strips and you’re making short, vertical cuts, the quickest and cleanest way to work is with a circular saw. If you’re only cutting a few strips of vinyl and making vertical cuts, using a pair of tin snips is simplest.
How many teeth do you need to cut vinyl?
Use one that has between 80 and 100 teeth to make smooth, fine cuts. Circular saws can produce the same type of cut as a miter saw because they use a similar cutting blade. This high tooth count blade by DeWalt makes smooth cuts and slides through vinyl quickly to keep from melting.
What do I use to cut vinyl lattice?
The best way to cut vinyl lattice is to use a circular saw and a cutting blade. Most of the people who usually need to do it regularly, suggests using a circular saw and a sharp and new cutting blade. You can also use a trim saw or a handsaw.
How do you cut vinyl siding lengthwise?
Fit your circular saw with a fine-toothed plywood-cutting blade (installed backwards for the cleanest cuts). Put on your safety goggles, then line up the place you want to cut on your siding with your blade. Use the edge of your table as a guide and slowly saw off the excess siding.
Why do you need to leave a ¼ expansion joint when installing vinyl siding?
Allow for Expansion and Contraction Vinyl siding installation must allow for material expansion and contraction caused by weather. Cut your siding in lengths with a 1/4-inch gap for expansion wherever siding butts accessories.
What is a 40 tooth saw blade used for?
Deep gullets provide good chip removal. Crosscut blades, made for cutting across the woodgrain (across the face of a board), have between 40 and 80 teeth and are designed for clean cuts. Smaller gullets separate the teeth. Combination blades can make both rip cuts and crosscuts.
What is a 60 tooth saw blade used for?
A crosscut blade, on the other hand, is designed to produce a smooth cut across the grain of the wood, without splintering or tearing. This type of blade will usually have 60 to 80 teeth, and the higher tooth count means that each tooth has to remove less material.
Is more teeth on a saw blade better?
More teeth means a smoother cut, fewer teeth means that the blade removes more material. Crosscut blades have more teeth and make smoother cuts across the grain of the material, rip blades have fewer teeth, are optimized to cut with the grain, and remove a lot more material.
How do you cut a lattice with a circular saw?
Position the circular saw blade at one end of the lattice sheet, lining up the blade with the marked cutting line. Squeeze the saw’s trigger, and move the circular saw slowly along the full length of the marked line. If necessary, walk on the lattice to the side of the lumber opposite the saw and marked line.
Is vinyl lattice hard to cut?
Vinyl fence and lattice can be cut just like wood material. Whether you’re installing your own fence, or doing some other vinyl fence project, chances are you will need to cut your material to custom fit your needs.
What side of vinyl do you cut?
The clear carrier sheet is the “shiny” side. The shiny side goes down when your cutting. The vinyl side goes face up. You want to cut through the vinyl, but not through the carrier sheet.
How do you cut already installed vinyl siding?
A rotary tool is the best tool for cutting siding that is already hanging. You can also make curved cuts with a rotary tool fitted with a mini saw blade or a zip tool, which is a cutting bit that looks like a drill bit.
What does F channel do?
F-channel is used to hold the soffit onto your house. Soffit is the vinyl siding that makes a ceiling under an overhang. The F-channel is a thin vinyl strip that is sold where siding is sold. The upside down F creates a shelf for the soffit to slide into and rest on.
