Cut the angle first with the saw at 90 degrees, and then use the off-cut to support the saw while you cut. If you grab your jigsaw whenever there’s a curve to cut, next time try your circular saw instead. It’ll do a sterling job for long, gradual curves in a fraction of the time a jigsaw will. If you’re cutting plywood, set the saw to cut just deep enough to cut through the wood.
Let’s just say that if you have a circular saw, you can quickly make 9 different cuts with it-cuts that you could also make with a table saw. It’s hard to say what the “Best” circular saw is because it depends on how you’ll use the saw, what you’ll be cutting, and your general preferences. Both the circular saw and the jigsaw are two of my favorite power tools and I use them interchangeably to cut wood, but the biggest difference between a circular saw and a jigsaw are the blades, type of cut, the thickness of the material that can be cut, and the type of materials that can be cut.
Bring the saw up to full speed, lift the guard, and slowly push the body of the saw down to start the cut. TIP: Make sure to start back far enough so that you only push the saw forward; never drag a spinning saw back. If a board is too wide for the saw shoe to hang over the edge during a rip cut, hold a narrow scrap of wood between thumb and forefinger, bracing your finger along the edge of the board, and butt the saw shoe against the edge of the wood scrap as you push both along the board.
how does a circular saw look like Related Question:
What is a circular saw used for?
The circular saw is perhaps the most commonly used saw today, used extensively in both professional construction projects and DIY home improvement. This power tool uses a round metal blade edged with sharp teeth to cut an array of material such as woods, metals, cement block, brick, fiberglass, plastics and slate.
How do you use a circular saw without a table?
Fit your circular saw with an edge guide. Set the depth of the blade accurately enough for it to go through the wood and not cut under the surface. Place the guide on base of the circular saw lines and markings you made earlier on the wood. Ensure that the saw is free to move, and the power cord is not entangled.
What are the 3 basic types of circular saw blades?
They are: Rip Blades, Crosscut, Combination and Specialty blades. Ripping saw blades are designed primarily to achieve a smooth, clean and safe cut when ripping wood or cutting in the same direction as the wood grain.
What is the difference between a table saw and a circular saw?
Circular saws are lightweight, hand-held, and can be moved from jobsite-to-jobsite with ease. A table saw is heavier and more complex in its set up. Because of its weight and footprint, this tool is more difficult to move these saws around as easily as you are able to do with a circular saw.
How shallow can a circular saw cut?
Circular saws turn corners about as well as a freight train, and standard models will cut only about 2 1/2 inches deep. There are ways around the shallow cut—for example, you can flip over a 4×4 and cut from two sides—but the curve limitation has no work-arounds.
How thick wood can a circular saw cut?
Generally, the blade of a circular saw can cut wood of thickness up to 2.5 inches. Depending on the thickness of the wood being cut, you need to change your blade’s depth. Since your wood is thick, ensure you are using Carbon-tipped blades. Use a crosscut blade for smoother cuts and rip blades for grain cuts.
Can I use a jigsaw instead of a circular saw?
Although a jigsaw can be used for most of the tasks that a circular saw can perform, including straight cuts and cuts on a tilt, the jigsaw uses that really take advantage of the tool’s qualities are jobs such as kitchen fitting and joinery, with their frequent need for complex cuts.
Can circular saw cut curves?
Circular saw technique The first tool that comes to mind for cutting curves is a jigsaw, but if the curve is gradual, try a circular saw instead. It’s surprisingly quick and easy to cut a smooth curve with a circular saw. This method is for cutting rough curves. Don’t try to make furniture with this technique.
Can you cut wet wood with a circular saw?
If you’re cutting wet wood set the depth so that the entire gap between the teeth is clear of the board you’re cutting. This will stop your saw and cut line from getting clogged with wet saw dust.
How do you use a circular saw without a sawhorse?
In some cases, it might be better to use your circular saw without a sawhorse. If you need to make cuts without a work support, you can lay a sturdy, stationary surface under the material while making cuts.
Can I use a circular saw as a table saw?
A circular saw won’t cut as smoothly as a table saw, but with a couple of techniques, a little finesse and some practice, you can cut almost as accurately.
How do I know if I need a new circular saw blade?
Look for worn-down, chipped, broken and missing teeth or chipped carbide tips that indicate it’s time to replace a circular saw blade. Check the wear line of carbide edges using a bright light and magnifying glass to determine if it’s beginning to dull.
Can a circular saw cut concrete?
Contractors and homeowners use circular saws to cut large pieces of wood, metal, brick, plastic and even concrete. These saws provide a great deal of capacity and precision, but cutting concrete with a circular saw is not an easy job for beginners.
Can a circular saw cut metal?
Cut Metal with Your Circular Saw It may not be an obvious choice, but fitted with the right blade, a circular saw is a great metal-cutting tool. In our test, it cut through rebar like a hot knife through butter. You can cut mild steel up to about 3/8 in. thick using a ferrous-metal-cutting blade.
Can a circular saw cut a 4×4?
Circular Saw. A circular saw is one of the best means of cutting a 4×4 post. Most people own a circular saw, its portability makes it easy to cut 4x4s from the ground, and they can make precision cuts by using a relatively simple trick.
