What is kickback? Kickback happens when the saw blade binds or stalls suddenly in the wood and the saw gets driven back toward you. So the key to preventing this is to make sure your blade doesn’t bind in the wood.
I thought it would be good to put together an article on handling circular saw kickback and throw in some additional safety tips that will make your experience better with these valuable tools. Kickback happens when the saw blade binds or stalls suddenly in the wood and the saw gets driven back toward you. In the comments field, feel free to share any close calls or other tips you might have regarding kickback or circular saw safety.
HOW TO PROPERLY USE A CIRCULAR SAW AND PREVENT KICK BACK. Among professional tradesmen, on the farm, around the house and in the vocational shop, the circular saw is probably the most commonly used power saw, and perhaps the most commonly abused. PREVENTING PORTABLE CIRCULAR SAW KICKBACK. Kickback is a sudden reaction to a pinched blade, causing an uncontrolled portable tool to lift up and out of the work piece toward the operator. Above information taken from THE TOOL GURU: How to properly use a Circular Saw and prevent kick back.
A kickback happens when you saw a piece of wood and suddenly the blade binds or the board that you are cutting bows downward, this will pinch the blade, the blade will suddenly stop and the circular saw will be left off and come back in your direction. Kickback happens when the saw blade binds or stalls suddenly in the wood and the saw gets driven back toward you. The saw is more likely to bind and kick back if the blade is too deep.
Overusing a saw results in the overheating of saw blades. Overheating might be the result of using a dull or edgeless blade, extensive rubbing of the saw on the board, using the saw so abruptly or so slowly and improperly adjusted saw. The circular saw consists of two handles i.e., front and back.
circular saw kickback at end of cut Related Question:
Why does my circular saw kick back at the end of a cut?
Overheating a saw blade can cause it to warp and result in a kickback. Buildup of sap on the blades, insufficient set, dullness and unguided cuts, can all cause an overheated blade and kickback. Never set a blade deeper than is required to cut the work piece 1/8 in. to 1/4 in.
How do I stop my circular saw from binding?
Avoid circular saw blade binding But cutting a long board in half is different. You can hold one end, but the other must be free to drop or the blade will bind. The trick is to allow the cutoff end to drop slightly, but not so much that it completely snaps off before the cut is complete.
Why wont my circular saw cut all the way through?
Here are some reasons your circular saw keeps stopping: Make sure your work piece is properly supported so it doesn’t pinch the blade which could also cause kickback in addition to stopping. Damaged, warped, loose or dull blade. Motor malfunctioning or overheating. Cable problems like frayed cord or weak connection.
What makes a saw kick back?
Kickback occurs when the teeth of the saw blade, moving at tip speeds of 120 miles-per-hour impart sufficient force to cause the workpiece to move in a violent and unexpected manner. Skil saw kickback tends to throw the saw back at the operator, its blade often running over fingers as it moves backwards.
Why is my circular saw binding?
A circular saw binds because of failure to ensure proper blade depth; setting the blade too deep presents a danger because more blade surface is exposed while cutting than a properly set blade. When the saw is too deep, kickback and binding will be inevitable.
What is an anti-kickback shoulder on a saw blade?
Anti-Kick Saw Blades Saw Blades with anti-kickback shoulders that limit the amount of material that can safely be cut by each tooth. This virtually eliminates the kickback caused by overfeeding. Also called safety saw blades.
Do Anti-kickback pawls work?
The farther back from the rear of the blade, the less effective it is. Anti-kickback pawls should be the backup to the preceding two options – if you can’t, or don’t (despite your best efforts) prevent the kickback, the pawls will at least retard the return of the stock in your direction.
Why does my hand saw bind?
If the saw is being pushed through the material quickly or forcefully, and binding occurs, this can cause the blade to bend, as pressure is being applied by the user from behind, and the blade has nowhere to go.
Why does my hand saw keep binding?
The wood you are sawing is closing the kerf and pinching the blade, Your cut isn’t straight, The set of the saw teeth is not large enough, so the kerf created by the blade isn’t wide enough to allow the saw room to pass without undue friction, or.
What is the closest you should put your fingers to the blade while it is running?
Do not put your fingers closer than two inches from the blade. 3. Do not place your hands directly in line with the blade while cutting stock. 4.
Why is my circular saw stopping mid cut?
The circular saw stops in the middle of work when the blades of the saw are dull or damaged and are not functioning correctly. Moreover, it can also stop working when the motor of saw is not working properly. However, there could be some other reasons like cable issues, voltage issues etc.
Why does circular saw stop halfway through cut?
Too much blade will become exposed to wood, and the blade can get stuck. Proper use can also be a culprit causing your circular saw to stop mid-cut. Make sure you are moving the saw in a straight line or using a jig to keep the cut straight.
Why is my circular saw struggling?
Most of the time, a circular saw keeps stopping because the blade gets stuck in the wood or material. This is due to the blade not being powerful enough to get through the material. It could also be because the blade is damaged or the motor is malfunctioning.
What are anti kickback pawls?
Anti-kickback pawls are saw attachments that reduce kickback while operating a saw. They reduce the risks of injury and equipment damage. They can be installed on table and radial arm saws.
Can a circular saw blade break?
Making sure your saw blade is working properly is the best way to reduce downtime and increase production. There are many common causes that can cause blade failure from blade selection to cutting speeds, feed rates and improper break-in, to maintenance problems and more.
