Chainsaw chains usually break while the chainsaw is in use. It will fly off of the chainsaw at high speeds and can cause severe damage to whatever it touches, especially if the chain ricochets off of the impact site. Chainsaw chains break when they are incorrectly used and not maintained properly.
The most common cause of chainsaw chain damage and breakage is probably a lack of knowledge of properly using and maintaining a chainsaw. When you need to replace a part on your chainsaw, whether a chain or another part, never try to be frugal and save money by getting cheap or low-quality parts; one of the main causes of chain breaks in a chainsaw is a low-quality chain. You need to check the tension on the chainsaw chain before every use to ensure that you won’t use the chainsaw and the chain unexpectedly snaps.
Chainsaw chains can break and snap due to improper use and maintenance, using a poor-quality chain, and incorrectly assembled chain parts. Chainsaw chains can come apart, break, or snap, especially if you aren’t well-informed about correct chainsaw use and maintenance. Improper use, lack of maintenance, low-quality parts and improper chain tension are the main reasons chainsaw chains deteriorate and eventually break entirely.
I have had only two break on me, and both of them were on my 372.Both broke while in the cut, one when the tip grabbed a branch that I didnt see on the other side, the other broke for no reason at all. Both chains were shot anyway, both were filed down to the witness mark and ready to be retired anyway. Never have been hit by a broken chain, but there is always tomorrow…..
When a chain derails even at the highest speed, the drive links instantly disengage from the drive sprocket and the chain stops rotating when making contact with the saw. Most common is incorrect chain tension: ie the operator keeps cutting when the chain is visibly loose. Significant causes of loose chains are operator keeps cutting with a blunt chain, and the excess heat generated by that makes the chain stretch.
Another cause of chainsaw chain breaking is simply using the chainsaw while the tension of the chain is not adjusted properly. To prevent a chainsaw chain from breaking, don’t touch the running chainsaw blade on metal or stone. If your chainsaw chain broke, then to use it in the future it’s important to install a new and functioning chain.
do chainsaw chains snap Related Question:
What causes a chainsaw chain to snap?
Check your drive sprocket for wear. Sometimes if a slot has been worn in to the sprocket, and you tension to it, if the chain jumps to a higher point on the sprocket it can over tension. Check your drive sprocket for wear.
Why does my chainsaw chain keep breaking?
Chainsaw chains come off the bar due to worn-out bars, worn-out sprockets, and wrongly set tension. You should also note that with continued use, chains lose their tension and hence are more likely to come off the bar when you least expect it.
How long does a chainsaw chain usually last?
The lifetime of a chainsaw chain has no fixed limit and depends on usage and maintenance. The chain should last many years; 5-6 years should be no problem. However, if the chainsaw chain is used properly and taken care of, it can last way longer.
Can a broken chainsaw chain be fixed?
If you have decided to repair the chain, at this point you can do so. You can sharpen the chain with a chain sharpener, remove additional chains using the rivet punch or screwdriver if the chain has stretched, adjust the links in the chain, or replace damaged links in the chainsaw chain.
How long does a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
Do chainsaw chains stretch over time?
It’s perfectly normal for a chainsaw chain to stretch after regular use. But, if you allow your chainsaw to become too loose, it can easily come off and pose a dangerous situation for you. A chainsaw chain stretches and loosens from tension and extreme friction.
Why does my chainsaw jump when cutting?
Improper Chain Tension You can extend the life of your chain, bar and chain saw motor by maintaining the proper amount of tension on the chain. Too much slack in your chain can cause the saw blades to jump the bar. This is commonly referred to as throwing the chain.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How many times can I sharpen a chainsaw chain?
Cutters can be sharpened up to 10 times or more before the chain needs replacing. If your cutters are worn unevenly after a few sharpenings, a professional can regrind them to uniform shape. If you use the same chain for a few years, then buy a new one, the new one won’t mesh smoothly with the sprocket and bar.
How much does it cost to sharpen chainsaw chain?
A typical chainsaw can be sharpened up to 10 times before it’s time for a replacement. The cost to have a chainsaw sharpened ranges from $13 to $16. The average cost per chainsaw sharpening is $14.50 for people who choose to have their chainsaws professionally sharpened.
Do chainsaw chains have a master link?
Locate the master link that most manufacturers install to make removal of the chain a simple process. A visual inspection of the chain will reveal the master link due to its appearance that makes it stand out slightly from the other links.
Why is my chainsaw blade smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Are chainsaw bars hardened?
The solid chainsaw bar production begins with a solid bar of steel. The machine laser cuts the steel to the desired basic shape. That includes the outer contour, bores, and elongated hole. Looking at the process, the laser makes very little waste in the cut, and Stihl even reclaims the leftover steel.