The 6.5 will cut up to 2 1/16”, while the 7 ¼” cuts up to 2 ⅜”. Minor sure, but it’s when you tilt them into 45 degree angles, that the 7 ¼” can do something the 6.5 can’t. Cut through a 2×4.
This saw uses a 6 ½” blade, and this one uses a 7 ¼”. The 6.5 will cut up to 2 1/16″, while the 7 ¼” cuts up to 2 ⅜”. “Minor sure, but it’s when you tilt them into 45 degree angles, that the 7 ¼” can do something the 6.5 can’t. Whether you buy HART or another brand of circular saw, the choice between 6.5 and 7 saw comes down to this.
Beginners often get confused when it comes to 6.5 vs 7.25 circular saw. It’s not recommended to use either a smaller or larger blade on a circular saw than what the manufacturer recommends to use. A circular saw with a 7.25-inch blade would cut 4×4 materials without any issue.
Cuts While a 7.25 circular saw can cut through materials up to 4 inches thick, a 6.5 inches circular saw can cut through materials up to 2.5 inches. A 7.25 inches circular saw is heavier than a 6.5 inches circular saw. If you deal with wood occasionally, rather than regularly, a 6.5 circular saw will be the best saw for you.
One of the most common questions about a circular saw is how deep it can cut. What follows are the most common size of circular saw blades and their normal depth of cut at a 90-degree angle as well as a 45-degree angle. Obviously, a 90-degree cut provides the maximum cut capacity while the 45-degree bevel will limit the thickness you cut through.
how deep does a 6.5 inch circular saw cut Related Question:
How deep can a 6 1 2 circular saw cut?
Depth. A 6 ½ circular saw can cut materials up to 2.5 inches. It’s perfect for cutting small materials for a small DIY project.
How deep should a circular saw cut?
Don’t clamp both sides of a cut. For efficiency and safety, set the blade depth no more than 1/4-inch below the thickness of the board.
Can a 6 1 2 inch circular saw cut a 2X4?
Circular Saw Features The larger the blade, the deeper the cut. The most common blade diameter is 7-1/4 inches. Most saws with blade capacities of 6 inches or more can cut through 2-inch dimensional lumber at a 45-degree angle in a single pass.
Can a 6 1 2 circular saw cut a 4×4?
Like miter saws that measure less than 12 inches, a circular saw’s 6.5-inch or 7.25-inch blade will not cut cleanly through a 4×4. The maximum depth of most circular saws is just 2.5 inches. This means you’ll need to make two cuts. Having to make two cuts makes it easier to set up the cut.
How deep can a 5.5 circular saw cut?
It turns out that it’s a simple question but very essential when you are going to do a project using this kind of saw. To sum up, a standard circular saw can offer a cutting depth of 2.5 inches as the maximum, but you can adjust the depth to match your requirements.
How deep can a 7.5 circular saw cut?
Standard-size saws use 7 1/4-inch blades and can cut a maximum depth of about 2 1/2 inches.
Can a 5.5 inch circular saw cut a 2X4?
Yes! A 5.5 inch circular saw blade is perfect for cutting a 2X4. The blade capacity is deep enough to make a crosscut in 1 stroke. If you want to make a 45 bevel cut then you will need to make 2 strokes.
How deep will a 10 circular saw cut?
Makita 5104 14 Amp 10-1/4-Inch Circular Saw This large cutting capacity sidewinder can reach depths of 3 ¾ inches at 90 degrees, which allows users to easily cut into some timbers.
How shallow can a circular saw cut?
A circular saw with a 7 and 1/4″ blade can cut wood up a maximum depth (at 90 degrees) of 2.4375″. This means you can use a circular saw to cut a 2×4 board (which is actually 1.5″ thick).
Can you use a 7 blade on a 6.5 circular saw?
NO, a 7″ blade will not fit inside the blade guard. Also, it’s rough on these little saws cutting concrete or tile unless you reduce the blade size.
How thick of a piece of wood can a circular saw cut?
Generally, the blade of a circular saw can cut wood of thickness up to 2.5 inches. Depending on the thickness of the wood being cut, you need to change your blade’s depth. Since your wood is thick, ensure you are using Carbon-tipped blades. Use a crosscut blade for smoother cuts and rip blades for grain cuts.
What size circular saw will cut a 4×4?
Cutting a 4×4 with a Circular Saw – Guide If you need to cut a 4×4 post, then the ideal tool is a large 12” miter saw. This saw has the blade diameter needed to chop through a 4×4 in a single pass, so if this is an option for you it’s the way to go.
Can I use a bigger blade on my circular saw?
The answer is generally this is not a great idea. A larger blade will put excess stress on the motor, and may not have enough strength to provide the cutting power at the tooth you need.
Will a 4.5 inch circular saw cut a 2×4?
The new WORXSAW Compact Circular Saw is capable of cutting a 2×4 in a single pass. The compact circular saw features a 4-1/2 in. blade that is up to 50 percent lighter than a full-size 7-1/4 in.
How thick can a 5 1 2 circular saw cut?
The blade, located on the left side, cuts up to 1-3/4-inch at 90 degrees and 1-3/16-inch at 45 degrees.
