how to cut and join chainsaw chain Related Question:
Can you add a link to a chainsaw chain?
Align the hole in one of the links of the chain with the punch that presses the rivet out of the middle of the link and the flat base of the tool. Push down on the handle to apply pressure to the rivet until it pops out and releases the link. Snap the remaining links back together securely.
Can you fix a broken chainsaw chain?
If you have decided to repair the chain, at this point you can do so. You can sharpen the chain with a chain sharpener, remove additional chains using the rivet punch or screwdriver if the chain has stretched, adjust the links in the chain, or replace damaged links in the chainsaw chain.
What is a chainsaw chain drive link?
Gauge Measurement The parts of chainsaw chains that fit into the saw’s guide bar are called the drive links. The drive link is the bottom part of the chainsaw chain (see picture below). Gauge measures the thickness of the drive links if you were to look at them along the length of the chain.
Why does my chainsaw chain keep breaking?
Chainsaw chains come off the bar due to worn-out bars, worn-out sprockets, and wrongly set tension. You should also note that with continued use, chains lose their tension and hence are more likely to come off the bar when you least expect it.
Can you stretch a chainsaw chain?
It’s perfectly normal for a chainsaw chain to stretch after regular use. But, if you allow your chainsaw to become too loose, it can easily come off and pose a dangerous situation for you. A chainsaw chain stretches and loosens from tension and extreme friction.
What is a chainsaw sprocket?
What is the drive sprocket? The drive sprocket and the clutch drum are connected to the saw motor. The sprocket is designed to drive the proper-pitched chain around the guide bar.
How do I know if my chainsaw chain is worn out?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
How long does a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
Does it matter how many drive links are on a chainsaw chain?
For heavier jobs like felling trees or bucking logs, it might be better to have a longer chain with more links – but this will make it slower and less agile. Shorter chains can cut branches under two inches much faster than long ones because the short length of the blade doesn’t get caught up in them as much.
How many drive links does a 20 inch chainsaw chain have?
0.050 Gauge 3/8 in. Pitch Chainsaw Chain, 70 Drive Links.
What do numbers on a chainsaw chain mean?
If you are replacing a Stihl® chain, you can look at the numbers on the side of the chain to determine pitch, gauge, and other characteristics of the chain. Example: Your chain has the number 33RM2 stamped in the side of it. The first number represents the pitch: 1 = 1/4″ 2 = 0.325″
Why does my chainsaw jump when cutting?
Improper Chain Tension You can extend the life of your chain, bar and chain saw motor by maintaining the proper amount of tension on the chain. Too much slack in your chain can cause the saw blades to jump the bar. This is commonly referred to as throwing the chain.
Can a chainsaw blade snap?
Chainsaw chains usually break while the chainsaw is in use. It will fly off of the chainsaw at high speeds and can cause severe damage to whatever it touches, especially if the chain ricochets off of the impact site. Chainsaw chains break when they are incorrectly used and not maintained properly.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
Which is better Rim sprocket or spur sprocket?
Rim sprockets are better than spur sprockets because they are easy to maintain, offer increased flexibility and have a lower cost. Unless you have a very specific use case, you will be happier with a rim drive sprocket and so will your chainsaw.