Cut the angle first with the saw at 90 degrees, and then use the off-cut to support the saw while you cut. If you grab your jigsaw whenever there’s a curve to cut, next time try your circular saw instead. It’ll do a sterling job for long, gradual curves in a fraction of the time a jigsaw will. If you’re cutting plywood, set the saw to cut just deep enough to cut through the wood.
Whether you just got your first circular saw or you’re looking for some ideas of how to make better cuts, our Pros are here to help you learn how to cut with a circular saw. Learning how to make a straight cut with your circular saw is as simple as setting the square’s lipped edge against the side with one hand and cutting with the other. When we did our cordless circular saw shootout, how fast each saw cut was a big part of our data.
Using a guide to cut with your circular saw is a great way to ensure a straight cut and it’s quick to set up. Make a DIY guide to cut a straight line You can easily make your own cutting guide to use with your circular saw. Final Thoughts on Cutting a Straight Line with a Circular Saw Circular saws can certainly be tricky, especially when making straight cuts – so hopefully you’ll be more confident than ever on your next cut.
If you’re not an experienced user, your best bet to make straight cuts every time is to use a circular saw guide like the Kreg rip-cut guide. It’s great for making straight rip cuts, repeat cuts, and most important of all, you get to make straight cuts every time as you push the circular saw along the slide. Follow the above steps, and you’ll make straight cuts with your circular saw every time.
how to cut circular saw Related Question:
Can you use a circular saw to cut?
The common types of cuts we’ll make with our circular saw are rip cuts, crosscuts, and miter cuts. A rip cut is made with the grain of the wood or along the length of the board. A crosscut is made across the grain of the wood or across the width of the board.
Which side of the line do you cut with a circular saw?
When appearance matters, make cuts with the good side facing down, as circular saws can splinter the wood on the top side. Making your cut line on masking tape can reduce splintering. Start over if you see that you’ve veered off from the cut line instead of trying to curve your way back on track.
Which way should the teeth face on a circular saw?
The teeth should be cutting UPWARDS, in a clock-wise direction. You’ll also notice that when your blade is installed correctly, the teeth will be pointing upward. Remember: circular saws (as most saws) cut on the upward stroke.
Why do circular saws cut upwards?
The teeth of circular saw blades are intended to cut upwards into the material from below and this is for safety purposes. It is important that you should not spin them in a different direction just like you spin a table saw blade.
When cutting wood which side goes up?
Your plywood should be oriented so that the blade exits the wood on the good face. So for a circular saw and miter saw, make your cuts with the good face down; on the table saw, with the good face up.
How do you use a circular saw without a sawhorse?
In some cases, it might be better to use your circular saw without a sawhorse. If you need to make cuts without a work support, you can lay a sturdy, stationary surface under the material while making cuts.
What is the difference between a circular saw and a table saw?
Circular saws are lightweight, hand-held, and can be moved from jobsite-to-jobsite with ease. A table saw is heavier and more complex in its set up. Because of its weight and footprint, this tool is more difficult to move these saws around as easily as you are able to do with a circular saw.
Can I use a jigsaw instead of a circular saw?
Although a jigsaw can be used for most of the tasks that a circular saw can perform, including straight cuts and cuts on a tilt, the jigsaw uses that really take advantage of the tool’s qualities are jobs such as kitchen fitting and joinery, with their frequent need for complex cuts.
Why does my circular saw burn the wood?
A dull blade will make it hard to cut quickly, and the slower the feed rate of the saw, the more friction against the wood and the greater the likelihood of scorch marks. Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty.
Can I put a metal cutting blade on my circular saw?
Only blades and discs specified for cutting metal should be used. These professional circular saw blades are perfect for cutting through aluminium, copper, lead and other non-ferrous metals; while these diamond cutting discs will make light work of cutting through stainless steel.
What kind of cuts can you make with a circular saw?
With the right blade, a circular saw can be used to cut framing lumber, sheet goods, roofing, metal, masonry, and more. A powerful saw can be a major time-saver during demolition as well. Once you get used to using your circular saw, you can even use it to cut curves, like I did on my backyard deck.
When using a circular saw be sure to cut on the waste side of the cut mark to allow for the blades?
Never use a circular saw that does not have an upper blade guard because the. guard protects you from touching the blade. When using a circular saw,be sure to cut on the waste side of the cut mark to allow of the blade’s. Saws with fine blades that are excellent for delicate and intricate cutting are called.
Can you cut wet wood with a circular saw?
If you’re cutting wet wood set the depth so that the entire gap between the teeth is clear of the board you’re cutting. This will stop your saw and cut line from getting clogged with wet saw dust.
Which cut is when you cut a straight 90 degree across the grain?
A crosscut is a straight, 90-degree cut that cuts across the grain of the wood. Usually, that means turning long boards into shorter ones. On a table saw, you will usually use a miter gauge to make crosscuts. It’s the most basic cut you can make.
What size circular saw Do I need to cut 2×4?
You need a minimum 5-3/8 inch size circular saw blade to cut a 2X4 at a 90 degree angle in one cut which is a crosscut. If you want to cut a 45 degree bevel with this size circular saw it will take 2 cuts. You could go with a 7-1/4inch or 10 inch blade to avoid making multiple cuts with the 45 degree bevel angle.
