Learn how to safely saw boards freehand, cut plywood with a straightedge guide and build a ripping jig for accurate cutting with a circular saw. It’s usually easier to cut long pieces of plywood with a circular saw and a straightedge than to wrestle unwieldy sheets through a table saw. We’ll show you how to use a circular saw to quickly and accurately cut long boards and plywood, and give you plans for a handy cutting guide attachment for your saw.
how to use a circular saw long cuts Related Question:
How do you make a deep cut with a circular saw?
Set the blade depth before cutting Determine the blade depth by unplugging the saw and holding it alongside your board with the blade guard retracted. Then loosen the depth-adjusting lever or knob and pivot the saw’s base until the blade extends about 1/4 to 1/2 in. below the board.
How do you cut a long board in half with a circular saw?
But cutting a long board in half is different. You can hold one end, but the other must be free to drop or the blade will bind. The trick is to allow the cutoff end to drop slightly, but not so much that it completely snaps off before the cut is complete.
How deep can a 12 inch circular saw cut?
To sum up, a standard circular saw can offer a cutting depth of 2.5 inches as the maximum, but you can adjust the depth to match your requirements. It’s easy by moving the blade up and down to align against the material before starting to cut.
How deep can a 7 inch circular saw cut?
Circular Saw Sizes Standard-size saws use 7 1/4-inch blades and can cut a maximum depth of about 2 1/2 inches.
Why do circular saws cut upwards?
The saw’s motor runs the blade rotation in a way that the circular saw teeth direction points up as it enters the wood you’re cutting. It’s intentional to create the most stable, accurate, and safe cutting. As the blade teeth hit the material, they rip from the bottom through the top.
Why wont my circular saw cut all the way through?
Make sure your work piece is properly supported so it doesn’t pinch the blade which could also cause kickback in addition to stopping. Damaged, warped, loose or dull blade. Motor malfunctioning or overheating. Cable problems like frayed cord or weak connection.
Why does my circular saw kickback at the end of a cut?
Overheating a saw blade can cause it to warp and result in a kickback. Buildup of sap on the blades, insufficient set, dullness and unguided cuts, can all cause an overheated blade and kickback. Never set a blade deeper than is required to cut the work piece 1/8 in. to 1/4 in.
Can a 10 miter saw cut 2×12?
The bigger the blade, the deeper and wider its maximum cut. Typically, a 10-inch miter saw will cut a 2 x 6 at 90 degrees and a 2 x 4 at 45 degrees; a 12-inch miter saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees.
Will a 4.5 inch circular saw cut a 2×4?
The new WORXSAW Compact Circular Saw is capable of cutting a 2×4 in a single pass. The compact circular saw features a 4-1/2 in. blade that is up to 50 percent lighter than a full-size 7-1/4 in.
How deep can a 10 inch circular saw cut?
Makita 5104 14 Amp 10-1/4-Inch Circular Saw This large cutting capacity sidewinder can reach depths of 3 ¾ inches at 90 degrees, which allows users to easily cut into some timbers.
Can a circular saw cut a 2X4?
Yes, a 7-1/4 inch circular saw has plenty of blade depth to cut a 2X4. This blade size can even make quick and easy 45 degree angle bevel cuts through a 2X4.
Can a 6.5 circular saw cut a 2X4?
The 6.5 will cut up to 2 1/16”, while the 7 ¼” cuts up to 2 ⅜”. Minor sure, but it’s when you tilt them into 45 degree angles, that the 7 ¼” can do something the 6.5 can’t. Cut through a 2×4. Of course more capacity, typically means more weight.
Can a 5.5 inch circular saw cut a 2X4?
The Ryobi cicular saw is a 5.5″ saw, and it can cut a 2×4, just barely.
Is it okay to cut wet wood with a circular saw?
If you’re cutting wet wood set the depth so that the entire gap between the teeth is clear of the board you’re cutting. This will stop your saw and cut line from getting clogged with wet saw dust.
What is the space between two protruding teeth on a saw blade called?
Gullet (handsaw) The space between a saw’s teeth, where the saw dust is carried out. It is an equilateral triangle, just like the file that shapes the teeth.
