Cut the angle first with the saw at 90 degrees, and then use the off-cut to support the saw while you cut. If you grab your jigsaw whenever there’s a curve to cut, next time try your circular saw instead. It’ll do a sterling job for long, gradual curves in a fraction of the time a jigsaw will. If you’re cutting plywood, set the saw to cut just deep enough to cut through the wood.
In the fourth Circular Saw 101 video, This Old House contributor Mark Clement demonstrates how to properly operate the shoe of the circular saw. Some saws contain notches on the shoe that can help you align the saw with the correct cutline for cutting at 90 degrees or at unique angles.
Whether you want to make straight cuts with a circular saw by guiding it against a rafter square or straightedge or just follow a line freehand, even the best circular saw needs adjustment for accurate cutting. To fix a saw with an out of alignment shoe, check the manual or the brand’s technical service department for advice. If bolts connect the body of the saw to the shoe, you may have to loosen all of them and re-tighten them with the saw twisted in the desired direction.
Learn how to use your circular saw to make laser-accurate straight cuts! Here are four sure-fire ways to cut precise straight lines on boards and plywood! Breaking down sheets of plywood or MDF. Tips for Cutting Straight with a Circular Saw Position the speed square, DIY circular saw cutting guide, or Kreg Accu-Cut so it covers the side of the workpiece you want to keep. There are four ways to make straight cuts with a circular saw.
how to line up circular saw Related Question:
Which side of the line do you cut with a circular saw?
When appearance matters, make cuts with the good side facing down, as circular saws can splinter the wood on the top side. Making your cut line on masking tape can reduce splintering. Start over if you see that you’ve veered off from the cut line instead of trying to curve your way back on track.
How do I make an accurate cut with a circular saw?
Using a Straightedge for Accurate Circular Saw Cuts Measure the exact distance from the edge of the circular saw’s shoe to the same side of the blade. Once you have that measurement, add it to your original marks and make a new line. Set the straightedge on the new marks, clamp it down, and make your cut.
Why wont my circular saw cut straight?
What Causes a Circular Saw to Not Cut Straight. A faulty circular saw is likely to have issues such as an unstable blade or a warped blade edge. The problem could also be the way you operate the saw. If you do not operate the circular saw properly, it will not cut straight.
What causes a circular saw to bind?
A circular saw binds because of failure to ensure proper blade depth; setting the blade too deep presents a danger because more blade surface is exposed while cutting than a properly set blade. When the saw is too deep, kickback and binding will be inevitable.
How do you cut straight with a circular saw without a guide?
To ensure a straight cut, press the saw firmly against the straightedge as you push it along. Clamp a perfectly straight board or metal straightedge to a sheet of plywood to make cabinet-quality straight cuts.
When cutting wood which side goes up?
Your plywood should be oriented so that the blade exits the wood on the good face. So for a circular saw and miter saw, make your cuts with the good face down; on the table saw, with the good face up.
Will a circular saw cut a 4×4?
Circular Saw. A circular saw is one of the best means of cutting a 4×4 post. Most people own a circular saw, its portability makes it easy to cut 4x4s from the ground, and they can make precision cuts by using a relatively simple trick.
Can a circular saw cut curves?
Circular saw technique The first tool that comes to mind for cutting curves is a jigsaw, but if the curve is gradual, try a circular saw instead. It’s surprisingly quick and easy to cut a smooth curve with a circular saw. This method is for cutting rough curves. Don’t try to make furniture with this technique.
Why does my circular saw Buck?
Overheating a saw blade can cause it to warp and result in a kickback. Buildup of sap on the blades, insufficient set, dullness and unguided cuts, can all cause an overheated blade and kickback. Never set a blade deeper than is required to cut the work piece 1/8 in. to 1/4 in.
Why does my circular saw blade stop spinning?
The most common reason your circular saw blade stops spinning is because your workpiece is pinching the blade. This can also cause the blade to kickback. To prevent this from happening you need to support your workpiece properly to allow it to set securely through the entire cut.
Why does my saw get stuck?
The wood you are sawing is closing the kerf and pinching the blade, Your cut isn’t straight, The set of the saw teeth is not large enough, so the kerf created by the blade isn’t wide enough to allow the saw room to pass without undue friction, or. Your saw teeth are too fine for the wood you’re sawing.
What is the closest you should put your fingers to the blade while it is running?
Do not put your fingers closer than two inches from the blade. 3. Do not place your hands directly in line with the blade while cutting stock. 4.
Does a circular saw cut straight?
Despite its name, the portable circular saw (or any circular saw, for that matter) cuts only straight lines. The name actually refers to the shape of its blade.
