Starting an Echo chainsaw involves a process that is simplified by the chainsaw’s design. Pull the starter cord until the engine attempts to start. Push the choke control completely in and pull the starter cord to start the engine.
Place your chain saw in a safe starting position, on the ground with no obstructions. Put on your hearing protection, safety gloves and safety glasses and get ready to start the chain saw. Make sure the chain saw warms up for several minutes at idle before starting to cut.
Saw Chain Only use saw chain designated as, “LOW-KICKBACK,” that meets ANSI B175.1 or CSA Z62.1,.3 Standard when tested on the representative sample of chain saws below 3.8 C.I.D., and ECHO guide bar specified. Idle Speed Adjustment: Start engine, turn Idle Speed Adjustment Screw “T” CW until the saw chain begins to move, then turn screw out CCW until the saw chain stops moving. Pitch Chain brake Automatic band brake type Idle speed 3,200 RPM Clutch engagement speed 4,200 RPM Wide open throttle speed 12,500 RPM Chain tensioner Side access system Guide bar 12, 14, 16 in Saw chain 91PX/91VG Standard features Front hand guard, Rear hand guard, Anti-vibration device, Throttle control lockout, Chain catcher, Spark arrestor muffler, Optional Kick GuardTM, * Technical data subject to change without notice.
There are two different starting scenarios for Echo chainsaws: starting a cold start and the other being a warm start. If the chainsaw does not start after 5 to 7 pulls on the starter rope use the cold starting procedure. The proper way of starting an echo chainsaw is by placing the chainsaw on the ground and gripping the handlebar with your left hand and applying downward pressure on the handle.
how to start echo chainsaw Related Question:
How do you start a chainsaw?
Place the chainsaw on flat, level ground. Make sure the bar is clear of obstacles and bystanders are at a safe distance. Engage the chain brake. Engage the safety switch and simultaneously pull the trigger switch to start the chainsaw motor.
Why does my chainsaw not stay running?
Your chainsaw’s engine needs the right supply of air to run properly. A clogged air filter can be the reason why your chainsaw won’t start or stay running. Find your chainsaw’s air filter and remove it. If it’s clogged or too dirty, wash it or replace it.
Why is it so hard to start a chainsaw?
The chainsaw’s engine is flooded with fuel. A fuel issue is one of the most common reasons why a chainsaw won’t start. If the operator has repeatedly been trying to start the chainsaw through the recoil starter system, they may have accidentally flooded the engine with fuel.
What is the easiest starting chainsaw?
The best gas-powered model, the ECHO 18 in. Gas 2-Stroke Cycle Chainsaw, is easy to start and has impressive cutting power.
What kind of gas does a Echo Chainsaw take?
Your Echo chainsaw is a two-stroke engine that takes a mixture of unleaded gasoline and two-stroke motor oil at a ration of 50 to 1. This mixture equates to one gallon of gasoline to 2.6 ounces of the two-stroke motor oil.
Is a chainsaw 2-cycle?
Chainsaws and weed eaters use the same type of motor: the two-cycle, or two stroke, engine. Unlike a larger engine on a car, these compact engines use fuel and oil mixed together to power a piston and crankshaft.
Can you use easy start on 2 stroke?
Yes, you can use starting fluid on a two stroke engine, but it must be used with CAUTION. Two stroke engines has OIL mixed with the gas for lubrication of the moving parts of the engine.
How long does a spark plug last in a chainsaw?
A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.
How do you start a high compression chainsaw?
A Measure of Pressure Unscrew the spark plug using a ratchet and screw the compression gauge in its place. Sometimes an adapter is needed to make a tight fit between the gauge and the chainsaw. Pull the starter rope a few times until the gauge stops moving. When it settles onto a number, you have an accurate reading.
Why does my chainsaw dies when I give it throttle?
If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
Why does my chainsaw stop running after a few minutes?
Re: chainsaw shuts down after a few minutes Sounds like a fuel supply issue. Fuel line, fuel filter, carb diaphragms, impulse hose, plugged carb screen, bad fuel, etc.