Tightening the screw will tighten the chain, and loosening will loosen the chain. Visit our Chainsaw Chains page to our inventory of available replacement chains and other chainsaw accessories. eReplacementParts.com stocks thousands of parts for many major chainsaw brands, including Echo chainsaw parts.
You must check the chain tension every time you use the chainsaw and make adjustments when necessary. The video below from Echo demonstrates the proper way to adjust a chain tension. Many new cordless chainsaws have a chain adjusting dial instead of a screw, which allows you to adjust the tension by hand.
Important: Always make sure the engine is turned off before you begin tensioning the chainsaw chain. Locate the chain tension adjustment points on your chainsaw. Common locations for adjustment points include the side cover and the front of the chainsaw.
how to tighten my chainsaw chain Related Question:
Why won’t my chainsaw chain tighten?
Turn the tension control screw to the right to tighten the chain and to the left to loosen it. Attempting to turn the tension screw without loosening the nuts first may be the reason you can’t tighten the chain. Tighten the nuts back into place when you have the chain properly adjusted.
Why does my chainsaw chain keep loosening?
Chain Not Set Properly One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.
What happens if a chainsaw chain is too loose?
A loose chainsaw chain increases the risk of kickback as well as the chances of the saw chain being thrown off the guide bar. Saw chain that is too tight can prevent the chainsaw from turning the saw chain or cause the chainsaw to heat up.
How often should you tighten chainsaw chain?
The chain isn’t actually becoming tighter—instead, as you turn the tensioning pin—it pushes the chainsaw bar out a little bit, which takes up the slack on the chain. During a typical afternoon wood-cutting session that lasts 2 to 4 hours, you may need to tighten the chain two or three times.
How much tension should a chainsaw blade have?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
Why is my chainsaw blade smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Why does my chainsaw blade go dull so fast?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
How long should a chainsaw blade stay sharp?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
Why does my chainsaw cut curves?
Two main reasons will cause the chain to cut on a curve. The most common reason is from improper hand filing. If one side of the teeth is more heavily damaged, sharpening them down will make them smaller than the other side.
Why do loggers run upside down bars?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
Does wet wood dull a chainsaw?
Does Cutting Wet Wood Dull a Chainsaw? Using your chainsaw to cut through wet wood will not dull the chain any faster than using it for other types of wood. When you think about it, your chainsaw chain is already wet. True, it is not wet with water.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How long should a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Why does my chainsaw bar get so hot?
If your chainsaw’s blade is overheating and producing smoke, it means that there is a serious problem with it. In that case, you must start troubleshooting at once. The two most common causes of the overheating or smoking of your blade are lack of lubrication of the bar guide or the engine and lack of air.