Cut the angle first with the saw at 90 degrees, and then use the off-cut to support the saw while you cut. If you grab your jigsaw whenever there’s a curve to cut, next time try your circular saw instead. It’ll do a sterling job for long, gradual curves in a fraction of the time a jigsaw will. If you’re cutting plywood, set the saw to cut just deep enough to cut through the wood.
The circular saw is often the tool of choice for making short, straight, clean cuts in a variety of common worksite materials, and you’ll wind up using one pretty regularly. If your work material rests directly on top of another surface, your circular saw blade may contact surfaces you don’t intend to cut. You’ll push the circular saw through the cut smoothly and purposefully.
how to operate a circular saw Related Question:
Which side should the blade be on a circular saw?
For blade-right models, the correct circular saw blade direction is usually with the label side out. For saws that have the blade on the left, it typically installs with the “ugly” side out.
Which way should the teeth face on a circular saw?
The teeth should be cutting UPWARDS, in a clock-wise direction. You’ll also notice that when your blade is installed correctly, the teeth will be pointing upward. Remember: circular saws (as most saws) cut on the upward stroke.
How shallow can a circular saw cut?
Circular saws turn corners about as well as a freight train, and standard models will cut only about 2 1/2 inches deep. There are ways around the shallow cut—for example, you can flip over a 4×4 and cut from two sides—but the curve limitation has no work-arounds.
Why does my circular saw kick back?
Overheating a saw blade can cause it to warp and result in a kickback. Buildup of sap on the blades, insufficient set, dullness and unguided cuts, can all cause an overheated blade and kickback. Never set a blade deeper than is required to cut the work piece 1/8 in. to 1/4 in.
How do you use a circular saw without a table?
Fit your circular saw with an edge guide. Set the depth of the blade accurately enough for it to go through the wood and not cut under the surface. Place the guide on base of the circular saw lines and markings you made earlier on the wood. Ensure that the saw is free to move, and the power cord is not entangled.
Where is the arbor lock on a circular saw?
Place the saw on a wooden surface and pull back the blade guard. If the saw has an arbor lock button on the top of the housing, press it in. The arbor is the shaft the blade installs on. If there’s no lock button, press the blade into the wooden surface.
Can a circular saw cut metal?
Cut Metal with Your Circular Saw It may not be an obvious choice, but fitted with the right blade, a circular saw is a great metal-cutting tool. In our test, it cut through rebar like a hot knife through butter. You can cut mild steel up to about 3/8 in. thick using a ferrous-metal-cutting blade.
Why does my circular saw burn the wood?
A dull blade will make it hard to cut quickly, and the slower the feed rate of the saw, the more friction against the wood and the greater the likelihood of scorch marks. Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty.
Why are my circular saw cuts curves?
A faulty circular saw is likely to have issues such as an unstable blade or a warped blade edge. The problem could also be the way you operate the saw. If you do not operate the circular saw properly, it will not cut straight. Let’s discuss several causes why your circular saw might not cut straight.
What PPE should you wear when using a circular saw?
Wear personal protective equipment, including safety glasses or goggles, faceshields, and hearing protection. Ensure all safety guards are in good working order before starting work. Ensure the saw’s blade is sharp. Sharp blades are safer and work better.
Do all circular saws rotate the same direction?
Circular Saws This means that the circular saw cuts wood on the upstroke. For a right handed circular saw (most common), this means that the blade rotates counterclockwise, which is similar to the table saw. For a left handed circular saw, the blade rotates clockwise.
Why are so many circular saws left-handed?
The placement of the cordless saw blade, on the left side, gives you a clearer line of sight when you cut. The reason for this is because the main bulk of your circular saw is not blocking your view. Cordless circular left-handed saws provide you better movability.
Can you put a circular saw blade on backwards?
When cutting vinyl siding with a circular saw, install a fine-toothed blade backwards on the saw for a smoother, cleaner cut, especially in cold weather (when the material is brittle).
Does the saw cut on the return stroke?
Answer. A hacksaw is the saw that cuts wood during the return stroke of the saw.
Can I cut a 4×6 with a circular saw?
However, a regular circular saw with a 7 1/4-inch diameter blade will only cut to a depth of 2 1/4 inches. Cutting on all four sides still leaves roughly an inch of uncut wood in the middle of the post. This is alleviated with either a handsaw, or reciprocating saw.
