Here are our favorite 9 circular saw jig plans we found while scouring the web. This plan is a very useful resource – and as you can see, the result is very professional looking – it would probably work best with a corded circular saw rather than a cordless circular saw or a mini circular saw. Although a circular saw with a jig can’t replace a good table saw or miter saw for all applications, it can open up a whole range of new possibilities.
A circular saw is perfect for slicing up plywood and other sheet goods so they’re safer to maneuver over a table saw. Unless you use a circular saw every day trying to eyeball a straight cut across a sheet of plywood is like steering a boat without a rudder. Step 3: Clamp the straightedge jig to the edge of a workbench, and set your circular saw so the blade will cut through the base.
Make a DIY circular saw crosscut jig! This simple cutting guide is perfect for making accurate crosscuts and precise miter cuts with your circular saw. You may also enjoy 4 Ways to Make Straight Cuts with a Circular Saw and How to Change a Circular Saw Blade. The common types of cuts we’ll make with our circular saw are rip cuts, crosscuts and miter cuts.
how to make circular saw jig Related Question:
Can you turn a circular saw into a miter saw?
We have seen circular saws used as table saw replacements with the Eurekazone tracksaw system, and now there is a new system from PUPS (Portable Universal Power Station) that can turn a circular saw to an accurate miter saw.
Can a circular saw make miter cuts?
When extreme precision isn’t required, you can cut 45-degree miters using a portable circular saw and speed square. 7. Hold the square against the board, then guide the saw along the square to make the cut.
How many teeth do you need for plywood?
Cross-cutting wood or sawing plywood: Use a 40-tooth to 80-tooth blade. You can use a 40-tooth to 50-tooth general purpose blade as well. Joinery work: Use a 40-tooth to 50-tooth all-purpose combination blade. Cutting MDF and man-made materials: Use a 50-tooth to 80-tooth blade.
When cutting plywood with a circular saw which side is up?
Also note that a circular saw cuts on the upstroke, which often splinters the top edge (veneer) slightly. The bottom edge usually remains splinter-free. So always cut plywood with the good side down.
How do you cut a plywood with a circular saw without splintering?
To do so, place the best side (meaning the side of the door that will be most visible once it’s hung) face down. Then score along the edge of the cut line with a sharp utility knife. Now when you make the cut, the wood fibers will break off cleanly at the scored line, leaving a smooth, splinter-free cut.
Why is my circular saw cutting crooked?
What Causes a Circular Saw to Not Cut Straight. A faulty circular saw is likely to have issues such as an unstable blade or a warped blade edge. The problem could also be the way you operate the saw. If you do not operate the circular saw properly, it will not cut straight.
Can you turn a circular saw into a chop saw?
Use the square to draw a line straight across, then use the circular saw to cut along that line. Unplug the saw. Tip: Half-inch poplar is thin enough to ensure the saw doesn’t rest too far above the wood you’ll eventually cut with this DIY chop saw, but it’s also strong enough to reliably hold the saw in place.
Can a circular saw cut 45 degrees?
Making 45-degree cuts with a circular saw might seem like an intimidating process, but with a little bit of preparation and practice, anyone can do this. There are two possible 45-degree angle cuts with a circular saw, a bevel cut, and a miter cut.
What is the difference between a compound miter saw and a miter saw?
Compound cuts include both a bevel and miter. A compound miter saw adds the ability to make bevel cuts in addition to its mitering ability. You’ll want to make sure you have this feature anytime you work with crown molding or other trim that gets installed on a wall.
Do I need a miter saw if I have a circular saw?
Why a Miter Saw Should Probably Be Your First Saw. Circular saws do have more versatility than miter saws. Every cut you can make on a miter saw can also be done on a circular saw, plus a few more. This is why my dad (and some others on the internet) recommend starting with a circular saw.
