Learn how to change a circular saw blade! We’ll see which direction to install the blade, how to tighten the blade, what size blade you need and more! Please refer to your owner’s manual for how to change the blade on your specific circular saw. Now we know how to change a circular saw blade! We learned which direction to install the blade, how to tighten the blade, what size blade we need and more!
Steps for changing a circular saw blade Unplug the saw’s power cord from the electrical outlet or extension cord. Use the blade wrench to tighten the arbor nut until it’s snug; be careful not to over-tighten the nut or it’ll be difficult to loosen it the next time you change the blade. If the saw has a diamond-shaped arbor, straddle the blade over two wood blocks and use a hammer or punch to tap out the diamond insert from the center of the saw blade.
how to change circular saw blade makita Related Question:
Where is the arbor lock on a circular saw?
Place the saw on a wooden surface and pull back the blade guard. If the saw has an arbor lock button on the top of the housing, press it in. The arbor is the shaft the blade installs on. If there’s no lock button, press the blade into the wooden surface.
Why won’t my miter saw lift up?
Depending on the model, it may require twisting, but typically is only an inward, outward movement of the pin. The blade should lift up automatically when the pin is released. The guard should cover the blade as it lifts. If it doesn’t, it’s likely dirty or stuck and should be cleaned to move freely with the blade.
Which way do the teeth face on a circular saw?
The teeth should be cutting UPWARDS, in a clock-wise direction. You’ll also notice that when your blade is installed correctly, the teeth will be pointing upward. Remember: circular saws (as most saws) cut on the upward stroke.
How do you hammer a circular saw blade?
Place the blade on the anvil. Hammer down all ridges or lumps while using as few blows as possible to avoid expanding the metal too severely. If there’s a loose area, mark it and hammer between the mark and the blade’s rim to stretch out unnecessary tension.
What size blade does a Makita track saw use?
Track Saw, 6 1/2 in Blade Dia., 13/16 in Arbor Size, Max.
Can you use Makita circular saw on guide rail?
Enables use of DHS680 Circular Saw with the Makita guide rail system. This adaptor can be attached to Makita circular saws, which allows you to use the circular saws with the Makita SP6000 guide rail system for precise, straight routing cuts.
What do you do with old saw blades?
The best thing to do would be to recycle them at a scrapyard near you. Donate them to a school that has wood shops, art departments, or theater programs. Make interesting pieces of jewelry such as earrings out of circular saw blades. You can use a jigsaw to cut and shape them the way you want.
How long do Diablo blades last?
That said, an average table saw blade will last about 2-4 years until it needs to be replaced. Sometimes, you don’t even have to replace your table saws blade… a simple cleaning and sharpening will do.
Is it worth sharpening circular saw blades?
When your circular saw blade becomes dull, not only will it give you a rougher finish, but your saw’s motor will have to work harder and may burn out sooner. Sharpening your saw blades will save you money in the long run because you’ll get better cuts, and you’ll have to replace your saw and blades less often.
Why does my circular saw not cut straight?
What Causes a Circular Saw to Not Cut Straight. A faulty circular saw is likely to have issues such as an unstable blade or a warped blade edge. The problem could also be the way you operate the saw. If you do not operate the circular saw properly, it will not cut straight.
How do you know if a circular saw is square?
Checking Circular Saw Accuracy at 90 Degrees Circular saws have two cutline marking notches, one for square cuts and another for 45° bevel cuts. To check their accuracy, start with the square-cut marker. Just about every saw we’ve ever tested has an adjustable set screw for this calibration.
