Generally, a fully functional chainsaw should cut straight and smooth, but if this does not happen, your chainsaw is likely to be faulty. The chainsaw bar can cause the chainsaw not to cut woods straight. The first step to solving any chainsaw problem is to understand the type of chainsaw suitable for your needs and how it operates.
When the saw teeth become chipped, damaged or dull, the chainsaw likely won’t cut straight, especially if more teeth are affected along one side of the chain. Sharpen the teeth uniformly using a file and file guide, or take it to professional for sharpening. Madsen’s recommends using a grinder rather than a file, if you want to avoid taking it to a professional.
Dull cutters damaged by rocks can cause a chain to cut crooked. It’s important to remove all damage from cutters prior to cutting. Cutting with a dull chain can accelerate wear to the bar and chain.
The most probable reason why a chainsaw pulls either to the right or left during a cut is because it was sharpened unevenly. Keep working the side which you feel lacks attention, and eventually the chainsaw should start going as straight as new. The teeth have to be equally sharp on each end to make the chainsaw work straight.
my chainsaw is cutting crooked Related Question:
Why does my chainsaw cut crooked?
Uneven top plates can cause a chain to cut crooked. It’s important to keep all top plates equal length. Dull cutters damaged by rocks can cause a chain to cut crooked. It’s important to remove all damage from cutters prior to cutting.
How do you fix uneven wood cuts?
Usually, the fixing method is to fill the gap with lots of glue and wood filler. But here’s a better method, take a small piece of wood and put it in the gap. Then glue it in the right place and clamp it to the side of the tenon. Make sure that you have arranged the grain of the wood.
Can a chainsaw bar be straightened?
Solid body bars with replaceable noses can be straightened by hammering with the bend peak up on a flat anvil. Laminated bars need a piece of rubberized belting of approximate 1/4″ thickness between bar and anvil to properly hammer straighten .
Why does my chainsaw bar keep bending?
A saw that has had one side of the chain nicked on a rock or dulled in the dirt will cut in a circle. A chain that has been sharpened differently on one side of the chain than the other will cut in a circle. A bent bar might cut crooked or straight, but, it will get hung up in the kerf.
Why is my chainsaw bar smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
How long does a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
Can you use a chainsaw horizontally?
Make a horizontal cut as close to the ground as possible. Go slow and keep the chainsaw steady. If you find that the chainsaw chain is getting pinched, use a wedge to keep a separation between the top and bottom layers of wood.
Can you cut with both sides of a chainsaw?
A chainsaw is one of the most versatile tools you can own, but it cuts both wood and flesh equally well.
How do you cut a perfect straight line in wood?
You can use both a jigsaw or a circular saw to cut wood in straight lines, but you will get the most accurate cuts, by using the circular saw. Nevertheless, the jigsaw is very versatile if you use the right cutting techniques.
Which cut is when you cut a straight 90 degree across the grain?
A crosscut is a straight, 90-degree cut that cuts across the grain of the wood. Usually, that means turning long boards into shorter ones. On a table saw, you will usually use a miter gauge to make crosscuts. It’s the most basic cut you can make.
How often should you flip the bar on a chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
How long should a chainsaw blade last?
The lifetime of a chainsaw chain has no fixed limit and depends on usage and maintenance. The chain should last many years; 5-6 years should be no problem. However, if the chainsaw chain is used properly and taken care of, it can last way longer.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
Why is my chainsaw blowing white?
Why is my chainsaw blowing white? While black smoke is caused by the burning of more fuel than air, blue or white smoke is generally caused by the burning of excess oil.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.