More info about why do chainsaws not cut straight

If a chainsaw cuts at an angle rather than cutting straight, then the problem most certainly lies in the guide bar and chain assembly. Adjust the chainsaw bar: If possible, adjust your chainsaw bar on a bench before continuing. Use a bar cleaner handle: A bar cleaner hook tool removes debris stuck in the bar’s rails.

Your chain will have links on both sides of the chain. As I mentioned earlier, the chain is most likely the root cause of your problem, but if that’s not it, then it could also be your chainsaw bar. Use your gauge tool to clean the oil hole on both sides of the bar, to keep your chain running smoothly.

Most of the time when a saw won’t cut straight, it’s caused by a problem with the saw chain. Most of the time, when a saw won’t cut straight, the chain is the culprit. Since a saw chain is a “Team” of cutter teeth, the cut will pull in the direction of the side whose cutter teeth take the biggest bites.

When the saw teeth become chipped, damaged or dull, the chainsaw likely won’t cut straight, especially if more teeth are affected along one side of the chain. Sharpen the teeth uniformly using a file and file guide, or take it to professional for sharpening. Madsen’s recommends using a grinder rather than a file, if you want to avoid taking it to a professional.

The most probable reason why a chainsaw pulls either to the right or left during a cut is because it was sharpened unevenly. Keep working the side which you feel lacks attention, and eventually the chainsaw should start going as straight as new. The teeth have to be equally sharp on each end to make the chainsaw work straight.

why do chainsaws not cut straight Related Question:

Why is my chainsaw cutting at an angle?

One major reason a chainsaw curves to either the right or left during a cut is that it was unevenly sharpened. The unequal teeth of the chain cause it to take a different-sized bite into the wood. What is this? The uneven sharpness of the chain is mainly due to manual sharpening, especially with the use of a file.

How do I stop my chainsaw from cutting crooked?

Check the size of the top plates, which sit on the longer sections of each tooth on the chain. These top plates should be the same size. If some are shorter than others, file the longer ones down to match. Keep the same angle on all the top plates as you file – angles that don’t match also can cause curved cutting.

Why does my chainsaw chain dull so quickly?

Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.

Why does my chainsaw smoke when cutting?

This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.

Why does my chainsaw burn the wood?

Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.

How long does a chainsaw bar last?

Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.

Can a bent chainsaw bar be straightened?

Solid body bars with replaceable noses can be straightened by hammering with the bend peak up on a flat anvil. Laminated bars need a piece of rubberized belting of approximate 1/4″ thickness between bar and anvil to properly hammer straighten .

How often should you flip the bar on a chainsaw?

Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.

Does hard wood dull a chainsaw?

Re: Chainsaw and oak Very hard but really puts out the heat in the fireplace. If you cut it green it is not too bad. After it has dried it will dull a chain about each tank of gas. And that was Stihl chain.

Is it worth sharpening a chainsaw chain?

Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.

Is it OK to cut wet wood with a chainsaw?

Can you cut wet wood with a chainsaw? Yes, you can cut the wet wood with a chainsaw. Besides, there is a misconception that wet wood can impact the chainsaw bar and chain. But actually, the damp wood will not dull the chainsaw any faster than using it on other types of wood.

Does dirt dull a chainsaw blade?

Nobody plans to run their chain saw into dirt. But when you cut close to the ground, you’re just begging for a quick dip into dirt, rocks and crud. All it takes is a second in the dirt to dull the cutters. In addition to dulling the cutters, dirt also wears out the chain links faster, causing the chain to stretch.

Why is my chainsaw chain not tightening?

If you’re having trouble tightening the chainsaw chain, it may be adjusted properly already. Check the tension on the chain by grasping it in the middle of the top of the guide bar and giving it a quick snap. The chain should quickly snap back into place with no sagging on the underside of the guide bar.

Can you over tighten a chainsaw chain?

There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.

Why do chainsaw chains stretch?

A chainsaw chain stretches and loosens from tension and extreme friction. The friction from cutting through wood makes the chain very hot and the heat causes it to loosen. The heat expands the guide bar and when it cools, the chain has stretched. The chain will also loosen as it wears down from use.

Leave a Reply

Your email address will not be published. Required fields are marked *