If the operator has repeatedly been trying to start the chainsaw through the recoil starter system, they may have accidentally flooded the engine with fuel. If you believe fuel has flooded the chainsaw engine, pull the starter cord several times while holding the throttle, dry and replace the spark plug, and then try starting the chainsaw again. Gasoline will start to deteriorate if left unused and sitting, so if the chainsaw hasn’t been started in a while, be sure to check that old fuel is not collecting inside the chainsaw.
Here, we look at the top 11 reasons why your chainsaw won’t start. Another common reason a chainsaw won’t start is that the sparkplug is old, dirty, damaged or not correctly attached. If the temperature is too low, it can make it hard to start a chainsaw.
The question of why won’t my chainsaw start can be very hard to answer since the smallest thing can make a perfectly fine chainsaw go from working to being a large paperweight. If a chainsaw sits for a long time and wasn’t stored properly it can cause you all kinds of headaches and be a reason your chainsaw won’t start. The carburetor of a chainsaw is important and can be the reason that the chainsaw won’t start and the fix can either be simple or expensive.
A chainsaw can be a very useful tool for homeowners and professionals alike, until it stops working! When your chainsaw won’t start, it can cause a setback with your project and could even set you back financially for repairs. In this chainsaw starting guide you’ll learn the common problems that can arise with chainsaws as well as possible solutions. The recoil starter assembly consists of several elements that initiate the engine when starting the chainsaw such as the recoil starter pulley and rewind spring.
chainsaw will not start Related Question:
Why can’t I get my Stihl chainsaw to start?
Dirty or clogged fuel tanks, dirty fuel filters and lines, loose fuel hoses, dirty air filters and a dirty carburetor can all restrict fuel flow. Check, clean and replace all the fuel system parts before moving into the internal engine, as gas problems create a majority of starting problems.
How long does a spark plug last in a chainsaw?
A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.
How long to wait if chainsaw is flooded?
Many people wonder if a flooded chainsaw will fix itself? The answer is yes, but not always. By letting the chainsaw sit for about 20 minutes it will allow some of the fuel inside the engine to evaporate.
Why does my chainsaw not stay running?
Your chainsaw’s engine needs the right supply of air to run properly. A clogged air filter can be the reason why your chainsaw won’t start or stay running. Find your chainsaw’s air filter and remove it. If it’s clogged or too dirty, wash it or replace it.
How do you clean a chainsaw carburetor?
Let the chainsaw run at low RPMs/idle for a while. This is to let the cleaner run through the carburetor, the fuel lines, and the idle engine. The cleaner will wipe remove the gummy residue blocking the components to create a clean passageway for the air and fuel. As the RPMs begin to increase, turn down the idle knob.
How long to wait if engine is flooded?
Perhaps the best remedy for a flooded engine is time. Simply open the hood of your car and let excessive fuel evaporate for as long as you can. After about 20 minutes try starting your car again without hitting the gas pedal.
Can you clean a spark plug with wd40?
WD-40 removes carbon residue and keeps moisture away from spark plugs and spark plug wires. WD stands for Water Displacement, so if your spark plugs are wet or you need to drive moisture away from ignition distributors, for example, WD-40 is a product you should have handy!
How do you bypass a primer bulb?
There should be a thin springy washer around the rubber bulb, that holds it in. Pry out, pull out bulb-insert new one, slip springy washer down over primer bulb, to keep it in place.
Do Stihl chainsaws have a primer bulb?
Re: What chainsaw compable to a Stihl MS 260 PRO has a primer bulb and starts easil. FWIW on most saws it takes about 6 to 8 pulls just to get the gas from the tank to the carb if they have sat for a spell . Just the nature of a diaphragm carb .
How often should you tune up your chainsaw?
Obviously this depends to some degree on how often and how heavily you use your chainsaw but experts generally recommend you get a professional service or check-up from every few months for heavier use to at least once a year for light use.
Can you use starter fluid to start a chainsaw?
If you do not use it often, then you are okay to use starter fluid to start the chainsaw up.
Can you use starting fluid to start a chainsaw?
Removing the air filter, spraying starting fluid into the carburetor and pulling the starting rope is another quick way to clear out the engine. Starting fluid creates a leaner fuel mixture that ignites more easily, and the operation of the engine clears out the combustion chamber automatically.