A circular saw is perfect for slicing up plywood and other sheet goods so they’re safer to maneuver over a table saw. Unless you use a circular saw every day trying to eyeball a straight cut across a sheet of plywood is like steering a boat without a rudder. Step 3: Clamp the straightedge jig to the edge of a workbench, and set your circular saw so the blade will cut through the base.
Make this simple circular saw jig and every cut will be perfectly straight! Just clamp the jig to your board and slide the circular saw along the fence. Be sure to keep the saw flat on the circular saw jig and slide it slowly along the edge. Of course, a table saw would make this cut in a fraction of the time it takes to set up this circular saw jig.
Here are our favorite 9 circular saw jig plans we found while scouring the web. This plan is a very useful resource – and as you can see, the result is very professional looking – it would probably work best with a corded circular saw rather than a cordless circular saw or a mini circular saw. Although a circular saw with a jig can’t replace a good table saw or miter saw for all applications, it can open up a whole range of new possibilities.
Circular Saw Rip Cutting JigGet more from your circular saw with our easy-to-make ripping jig. >> 3 Circular Saw Jigs Without CategoryHalf-lap joint jig for Circ Saw and Router”Cutting on-the-money rabbets for half-lap joints with a portable circular saw and handheld router is a breeze with this two-in-one jig.” Circular Saw Cutoff Guide for Posts”When I have to use a circular saw to cuts rabbets and dadoes in posts, I use a circular saw cutoff guide that I made from scrap plywood.”
circular saw jig for ripping Related Question:
How do you rip accurately with a circular saw?
Clamp a Straight Edge for Rip Cutting Slide the shoe against your straightedge and push the saw forward to make sure the blade touches your cutline. If it doesn’t, make small adjustments until you get it right on. Just remember you need to move both ends the same amount to get a proper cut.
Why does my circular saw kickback at the end of a cut?
Overheating a saw blade can cause it to warp and result in a kickback. Buildup of sap on the blades, insufficient set, dullness and unguided cuts, can all cause an overheated blade and kickback. Never set a blade deeper than is required to cut the work piece 1/8 in. to 1/4 in.
What can you use as a guide for a rip cut?
plywood with notches to fit 1/4-in., 1/2-in., 3/4-in. and 1-1/2-in. boards or plywood. The notches help hold the board tight to the saw table, and the top handle slides along the top of your fence.
Are Circular Saw Rip Fences universal?
No, fences are not interchangeable on any circular saw. There are different widths. You can get a universal replacement set that would most likely fit.
What does a rip fence do?
A rip fence provides a cutting guide that runs from the front of the table to the back. This is parallel to the cutting plane of the blade. A Miter gauge holds and guides material at a specific angle to make a precise cut. The locking mechanism pivots from 45 to -45 degrees and slides into a slot (miter slot).
How do you keep wood from Slivering when cutting?
Tape the wood. Run a piece of making tape over the wood before drawing the cut-line and then cut through the masking tape. Taping holds the surfaces of the wood together, helping to prevent splintering.
How do you prevent tearing when cutting wood?
Another thing you can do to prevent tearout involves our old friend blue tape. Just run a strip of blue masking tape along the cut line on the side that you anticipate tear out. The tape helps to hold the fibers in place during the cut, and usually the result is a clean crisp line.
How do you rip a 2×4 in half?
To rip a 2×4 so that all edges are square, set the rip fence for 3-3/8″ from the blade. Run the 2×4 through the saw. Now, lay the 1-1/2″ edge on the table and move the fence to touch the other side of the board. Run the board through the saw with the rounded edge touching the fence.
Can I rip pressure treated wood?
You can rip it down if you want then coat the cut side with the green pressure treat stuff IF you have a Menards as Depot and Lowes don’t carry it.
Can circular saw Replace table saw?
When wielded with enough skill and experience, a circular saw can replace a table saw. However, the time needed to accumulate the skills and knowledge makes a table saws’ price seen negligible in comparison.
How can you tell if circular saw kickback might happen?
Kickback happens when the saw blade binds or stalls suddenly in the wood and the saw gets driven back toward you. So the key to preventing this is to make sure your blade doesn’t bind in the wood.
Can a circular saw blade break?
Making sure your saw blade is working properly is the best way to reduce downtime and increase production. There are many common causes that can cause blade failure from blade selection to cutting speeds, feed rates and improper break-in, to maintenance problems and more.
What does the saber saw do?
The sabre saw, which is basically a portable jigsaw, moves up and down and may have a stroke of as much as 2.5 cm (1 inch). It can rip, crosscut, and make angle cuts. The portable chain saw has practically replaced the woodman’s axe and the two-man hand saw for felling trees.
What is the best saw to make a rip cut?
A table saw is the safest tool to use for most rip-cutting operations, but you should follow these procedures for safe work: Use a push stick—an expendable stick of wood about a foot long and a 1×1 inch square—to push the workpiece the last foot or so through the saw blade.
Will Home Depot rip wood for you?
Yes, Home Depot has a wood cutting area where they serve customers by cutting their wood to the size they need. Any of the wood that you purchase in-store will be cut for free in this area, however, they will not allow you to bring in your own wood from somewhere else.
