If you need to cut workpieces that must be cleanly and accurately joined together, a circular saw and a guide rail is the way to get this done. Clean, accurate cuts over and over are possible when using a guide rail. The saw is also compatible with other makes of guide rail.
Steps: Mark the cut line onto the workpiece, then measure the distance from the circular saw blade to the edge of the saw shoe. Guide the circular saw along the fence to trim the base to the proper width. Then guide the saw along the fence to make an accurate, perfectly straight cut.
I planned to replace it once I settled into my new house, but when the time came to build a room divider/bookshelf unit, I decided to build a couple of my own makeshift circular saw guides instead. The guides are compact and store easily. It’s quick, safe and especially useful when you need to cut a sheet of plywood down to size or to rip a long straight edge on a wide piece of lumber to prepare it for further ripping on a table saw. The only difference is that I put a 1 x 2 stop on the bottom, perpendicular to the 1 x 4 guide, which automatically squares the guide across the piece being cut.
using circular saw guide Related Question:
Can you use a guide rail with a circular saw?
A Guide Rail is designed to be used with a Circular Saw for creating precise and straight cuts every time.
Are guide rails universal?
The YouTool Guide Rail is universally suitable for almost all brands of saw, and is available up to 5 meters long.
Which way should the teeth face on a circular saw?
The teeth should be cutting UPWARDS, in a clock-wise direction. You’ll also notice that when your blade is installed correctly, the teeth will be pointing upward. Remember: circular saws (as most saws) cut on the upward stroke.
How do you cut a lattice with a circular saw?
Position the circular saw blade at one end of the lattice sheet, lining up the blade with the marked cutting line. Squeeze the saw’s trigger, and move the circular saw slowly along the full length of the marked line. If necessary, walk on the lattice to the side of the lumber opposite the saw and marked line.
Which side should the blade be on a circular saw?
For blade-right models, the correct circular saw blade direction is usually with the label side out. For saws that have the blade on the left, it typically installs with the “ugly” side out.
Can a circular saw cut metal?
Cut Metal with Your Circular Saw It may not be an obvious choice, but fitted with the right blade, a circular saw is a great metal-cutting tool. In our test, it cut through rebar like a hot knife through butter. You can cut mild steel up to about 3/8 in. thick using a ferrous-metal-cutting blade.
Can you use Makita circular saw on guide rail?
Enables use of DHS680 Circular Saw with the Makita guide rail system. This adaptor can be attached to Makita circular saws, which allows you to use the circular saws with the Makita SP6000 guide rail system for precise, straight routing cuts.
Why does my circular saw burn the wood?
A dull blade will make it hard to cut quickly, and the slower the feed rate of the saw, the more friction against the wood and the greater the likelihood of scorch marks. Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty.
Why do circular saws cut upwards?
The teeth of circular saw blades are intended to cut upwards into the material from below and this is for safety purposes. It is important that you should not spin them in a different direction just like you spin a table saw blade.
Is there a left and right handed circular saw?
Here’s a hint—it’s not by accident that manufacturers don’t call these “right-handed” and “left-handed” saws. Our Pros will tell you that it’s all about what you get used to and are comfortable with. In fact, most have both types of saws for different applications.
Can I rip wood with a circular saw?
One of the most common ways we use to make rip cuts with a circular saw is to clamp a straight edge. To do this accurately, you need to know the distance from the edge of your shoe to the blade. From your cutline, clamp both ends of your straightedge the distance you measured between the shoe edge and blade.
Can a 5 1/2 inch circular saw cut a 2X4?
Yes! A 5.5 inch circular saw blade is perfect for cutting a 2X4. The blade capacity is deep enough to make a crosscut in 1 stroke. If you want to make a 45 bevel cut then you will need to make 2 strokes.
How many teeth do you need for plywood?
Cross-cutting wood or sawing plywood: Use a 40-tooth to 80-tooth blade. You can use a 40-tooth to 50-tooth general purpose blade as well. Joinery work: Use a 40-tooth to 50-tooth all-purpose combination blade. Cutting MDF and man-made materials: Use a 50-tooth to 80-tooth blade.
When cutting plywood with a circular saw which side is up?
Also note that a circular saw cuts on the upstroke, which often splinters the top edge (veneer) slightly. The bottom edge usually remains splinter-free. So always cut plywood with the good side down.
Which cut is when you cut a straight 90 degree across the grain?
A crosscut is a straight, 90-degree cut that cuts across the grain of the wood. Usually, that means turning long boards into shorter ones. On a table saw, you will usually use a miter gauge to make crosscuts. It’s the most basic cut you can make.
