If there is too much fuel mixed with the air, the engine “Runs rich” and either will not run, runs with a lot of smoke, runs poorly or, at the very least, wastes fuel. There is an adjustable plate across the tube called the throttle plate, which controls how much air can flow through the tube. One of these screws controls how much fuel flows into the venturi at full throttle.
Just bought a used McCulloch Chainsaw on the cheap knowing that the fuel system needed work. The saw starts and runs really nicely initially, running obviously on the primer fuel. There was four total rubber lines in the saw, one obvious one going from the bar oil to the oiler system, two going into the fuel tank and one going from the bulb to the carb.
The overall flow of fuel depends on a healthy impulse line. An impulse line can create a vacuum inside the fuel pump. Again, the pressure will enter the impulse line and fill up the fuel chamber.
how does a chainsaw fuel pump work Related Question:
How does fuel pump work on Stihl chainsaw?
Answer: The impulse fuel pump follows the pressure physics. It simply applies pressure and then creates a vacuum. That vacuum then pulls the fuel inside the fuel pump.
Why does my chainsaw stop when I give it gas?
If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
What does a pulse line do?
The pulse line connects the pulse chamber. The pressure of the crankcase is pushed by the pulse through a pair on one way valves and fuel passes continuously, and in a correct measure, to power the engine.
Do Stihl chainsaws have a primer bulb?
Re: What chainsaw compable to a Stihl MS 260 PRO has a primer bulb and starts easil. FWIW on most saws it takes about 6 to 8 pulls just to get the gas from the tank to the carb if they have sat for a spell . Just the nature of a diaphragm carb .
How do I check if my fuel pump is working?
The fuel pump should make an audible noise if it’s working properly. Whack the fuel tank: Have an assistant crank the engine while you hit the fuel tank with a rubber mallet. If the vehicle starts during this procedure, it’s a pretty clear sign the electric motor inside the pump is bad.
How does a diaphragm type fuel pump work?
Diaphragm pumps contain a pump chamber whose volume is increased or decreased by the flexing of a flexible diaphragm, similar to the action of a piston pump. A check valve is located at both the inlet and outlet ports of the pump chamber to force the fuel to flow in one direction only.
Why does my chainsaw bog down when I hit the throttle?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
Why does my chainsaw dies when I turn it sideways?
Because the fuel covers the jets. When the bar points down or the saw is held sideways the jets no longer have fuel to cover them, it is air. The saw then runs lean and dies.
What causes a chainsaw to bog down when accelerating?
The reason for that may be you’re using the saw at altitude or the carburetor adjustment has simply slipped. The saw also won’t operate well at speed if the air filter or spark arrestor or carburetor are dirty.
How does carburetor accelerator pump work?
An accelerator pump is a device found on a carburetor that sprays a controlled amount of gasoline every time the throttle linkage is fully depressed. The amount of fuel introduced into the intake when the accelerator pumps is sufficient to start the engine.
What causes a carburetor to not get fuel?
No fuel at your carburetor can be caused by many things. It could be a simple issue like a fuel filter plugged so tight that no fuel can pass through. Another logical cause could be the fuel pump. If the fuel pump is electric, the 12-volt power may be shorted.
What connects to the carburetor?
The carburetor uses fuel from the fuel tank to supply gasoline to the engine. There is typically a hose or metal tube for this, called the fuel supply line, that connects to the carburetor.
What is fuel pump diaphragm made of?
It is made with plies of medium weight, square-woven cotton duck – or nylon. Combined with the oil-resistant properties of neoprene, it will operate effectively in an oil atmosphere.
How does a Mikuni fuel pump work?
As the diaphragm is influenced by the negative pressure from within the crankcase it draws the diaphragm down increasing the vol- ume within the pumping chamber. It simultaneously closes the outlet check valve, and opens the inlet check valve. This draws fuel from the inlet chamber into the pumping chamber.
Can I bypass a primer bulb on a chainsaw?
Unfortunately, the primer bulb can’t be bypassed. Because a primer bulb ensures a proper flow of gasoline to your carburetor. Otherwise, your carburetor will be flooded.