They have earned their target porting “Numbers” by experience which includes porting some saws too far. They can really make out with a particular model of saw, aka build it for torque, or build it for RPMs, or best yet, achieve the perfect combination. One word of advice though, once you get used to working with strong, woods-ported saws, your stock saws will seem like gutless junk.
There is a process called porting the chainsaw, which helps in achieving a higher compressor ratio within the saw chainsaw. The sole purpose of a wood porting chainsaw is to let it breathe better and make the exhaust system smoother. The process of porting your chainsaw requires prior expertise and experience.
These are the exact steps I follow to wood ports my chainsaws and got 10%-25% power gain. One more thing to add, if you are a homeowner, you might never need to woods port your chainsaw. If you use your chainsaw for milling, read our guide on portable chainsaw mill and chainsaw mill attachment for getting the most out of your chainsaw.
That’s what chainsaw porting means, to increase the power of its engine. Steps in how to port a chainsaw Step one: Open up and make the exhaust larger. There are others methods of chainsaw porting which has the same effect of power increase.
what does a ported chainsaw mean Related Question:
What does porting a chain saw mean?
Porting is altering the size and shape of the ports exhaust, intake and transfer, not necessary all of them though. This affects compression and port timing so it cant really just be done willy nilly ie making them bigger etc.
Why is my chainsaw sputtering?
A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
Can a chainsaw run without a muffler?
A chainsaw will run perfectly without a muffler but using it without the muffler is not recommended for two main reasons. Firstly, the muffler reduces the noise made by the saw, and secondly, it provides protection to the cylinder by keeping debris from getting in.
How hot does a chainsaw muffler get?
Re: Muff Mod & Temp; Allow me to re-Phrase I’m quite sure a chainsaw muffler will get well over 200 degrees. Even a car muffler, several feet from the engine, gets hot enough to boil water (212 degrees).
How do you clean a chainsaw piston?
A toothbrush and toothpaste (yes toothpaste) will clean up the piston better and with no wear.
Why does my chainsaw dies when I give it throttle?
If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
What causes chainsaw to bog down?
Many chainsaw operators first notice a problem with chainsaws bogging down when they’re using the chainsaw under load, and this is usually the result of poor air circulation. This issue is caused by a clogged air filter on the chainsaw.
Why does my Stihl chainsaw dies when I give it gas?
An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw stalls while it’s idling, adjusting the idle screw, which usually is marked LA, should help.
What are chainsaw mufflers made of?
Re: what type of metal is a 026 muffler made out of It is steel.
Where is the exhaust on a chainsaw?
Most Stihl chain saws have a muffler on the side of the machine that is opposite from where the operator stands. The muffler can be taken off a chain saw for maintenance or repair of either the muffler or an adjoining part on the chain saw, and then the muffler should be put back in place.